-
1" Male JIC to KF25 adapter (Harvest Right Adapter) fits any KF25 flange. Summit's stainless adapters contain 100% USA made precision billet steel. Why choose an adapter with multiple parts and more chances to leak? -
$4,999.99
The new SPD-8 Series Heads (FC55, 60mm, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. This 2 liter head comes with boiling flask! Can be upgraded to 5 liter flask, please call us. Short Path Distillation 8 Head in use at the lab: Instagram Demo
The condenser in this 60mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm.
Included with this head:
- Head Key Well 45/50
- Stopper Well 45/50
- High Temp GL18s (4)
- Flange Clamp 60mm
- PTFE O-Ring 60mm
- 2 Liter Boiling Flask
-
The Cold Trap Flask 2 Liter is a round bottom 45/50 flask that commonly attaches to a Summit Cold Trap. 100% Threaded Schott glass. Used in conjunction with the Rodaviss Screw Cap. This flask holds an extra liter than our original Cold Trap 1 Liter for extra fun. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Rodaviss kit not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap Flask 2 Liter -
The KF40 Bellow is a corrugated stainless steel pipe that connects to corresponding kf40 flanges. These malleable pipes allow for some error as apposed to hooking up a solid straight pipe. Available in 24 and 36 inch lengths. Don't forget other KF40 fittings and accessories: 100% stainless steel. 100% USA made. Bellow warning: Stretch and bend your bellow into position before installation. Engaging your pump(s) while not doing so could make the bellow jolt/jostle, putting stress on or damage glassware, voiding limited warranties. KF40 Bellow -
The Flange Adapter 100mm is used to convert a flanged 100mm boiling flask to a 55mm (55/50) standard taper. You could utilize a different head or use a reflux condenser, the possibilities are endless. Glass unit only, clamp and O-ring not included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Flange Adapter 100mm -
The Fraction Finder Ultra Sensitive figures out where components start and stop flowing to optimize separation. Making the SPD Process more precise and repeatable, Fraction Finding helps take the guess work out. Someone running a distillation can make better decisions if they knew exactly where they were in the distillation process. Scientists have developed expertise in this area to the point where they know what to expect. The Summit Research Fraction Finder does that for you and will be your best friend in short path distillation. Included with:- Ultra Sensitive sensor
- Mounting hardware
- Display screen
- Light-blocking tape
- Power Supply
- Sensor Cable
- User Manual and Quick Start Guide
- 1-Year Warranty
- Fraction Finder optical sensor with ultra-sensitive detector
- Magnetic locking mechanism
- Anodized aluminum apertures
- 90° strap rotation
- Currently only available in size 34
- Validated by Arometrix for use on distillation systems
- Currently being tested on reverse-phase chromatography processes
- Display and sight glass not included
Information common with all Fraction Finder sensors
These sensors are black for a reason:- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
Cold Trap 2 Hard Pipe with male 34/45 (from cold trap) and 34/45 female exit (to pumps). The straight pipe acts as a sight glass and is a great last line of defense to see if any moisture is reaching your pumps. Total length: 24.5 inches and 3.5 inches at top section. Hard pipe only, cold trap not included. Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distillation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. CT-2 Hard Pipe -
$16,710.00
Rebuilt Edwards E2M80 + Blower (mechanical booster) All air cooled dual stage Rotary Vane Pump, 208 V, 50 Hz/208-230 V, 60 Hz/460 V, 60 Hz, Three Phase with KF-40 inlet to blower. Edwards E2M series two stage oil sealed rotary vane vacuum pumps are renowned for their high ultimate vacuum, rapid pumping speeds, quiet operation and ability to handle water vapor. These direct drive rotary vane pumps are inherently compact and vibration free. Blowers add a dimension of vacuum that tops most dual pump options. Mechanical boosters feature the unique hydro-kinetic drive that provides pump down times cut by 50%, when compared with direct drive pumps, no bypass lines or pressure switches required, universal voltage motors, reduced capital and operating costs, air cooled motors – with water cooled options, and quiet, minimum vibration. Operating at relatively low pressures, the mechanical booster pump is not exposed to the same concentrations of corrosive process media as is the backing pump, which makes it highly reliable. Comes with Pump, Blower, MF100 filter and I 19 Standard fluid. To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
Out of stock
Head Key Well Extra Long 45/50 has 18.5 inch overall length. 12.5 inch length from bottom of the frosted taper. 15 bands. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Head Key Well Extra Long 45/50 -
$4,849.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo
150mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 150mm heads fit exclusively to Summit flanged boiling flasks:
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 150
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$5,224.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo
150mm clamp with O-ring and PTFE GL18s (4) included. 45/50 Key port and appropriate key & well stopper. 34/45 discharge port. Our 150mm heads fit exclusively to Summit flanged boiling flasks:
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 150
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$4,499.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo
100mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 100mm heads fit exclusively to Summit flanged boiling flasks:
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 100
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$4,299.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo
34/45 key, 100mm clamp with O-ring and PTFE GL18s (4) included. 34/45 discharge port. Our 100mm heads fit exclusively to Summit flanged boiling flasks:
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 100
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
The Extraction Finder is a real-time molecular monitoring system for botanical extraction, which is essential for consistently maximizing the amount of extracted compounds within a given plant material. This robust model will serve hydrocarbon and ethanol extractions. Not rated for use with C02 extractions. The robust housing, which fully encloses the molecular sensor, can be easily installed in-line in the extraction design on sanitary flange end clamps. A 30′ sensor cable feeds this information to a high-quality touch-screen, which displays real-time levels of Cannabinoids, Chlorophyll and Lipids. The Extraction Finder’s digital readout can be used to help operators learn about and dial-in their process, such as optimizing flow rate, solvent amount, filter efficiency, and general quality assurance and control. In the long run, this system will be your best friend in dialing-in the most effective standard operating procedures (SOPs). Extraction Sensor- Housed and enclosed by the Extraction Sensor Housing
- Connects and transmits to the digital display via 30′ sensor cable
- Plug and play – instantaneously analyzes the mixture flowing through the processing machine
- Attaches directly onto sanitary flange connections (1.5″ or 2″) at any point in your extraction line
- Houses the sensor, fully enclosing it from hazardous environments
- C1D1/D2 certification
- Tablet-sized display mounts directly onto a lab pole
- Connects and interprets the wavelength information from the sensor
- Touch-screen interface displays real-time molecular information about the contents of the extraction fluid throughout the process
- Includes long wiring, allowing it to be placed away from C1D1/D2 area
- Molecular Selection – Select from a growing list of key molecules, including Cannabinoids, Chlorophyll, and Lipids; see full list here
- Intensity Values – Track as molecular intensity levels increase and decrease throughout the process
- Data Logging – Record and export run data for traceability
- Software Updates – Upgrade to software releases easily from the field (extraction finder software)
- Maximum Pressure: 240Psi
- Temperature: -70°C(min); 150°C(max)
- Mounting Plate: Available as an add-on
- Product Dimensions: 6.79in(L) x 5.39in(W)
- Wavelength of Excitation: 365 nm
- Optical Detection Range: 300–1000 nm
- Lower Detection Limit: <1mg/mL (at a volume of 1 cubic centimeter of oil)
- Resolution: Spectral resolution is 15 nm max
- Flow Rate Limit: No flow rate limit
Lack of objectivity during the extraction process
The purpose of botanical extraction processes, regardless of solvent used, is essentially to introduce a solvent to the biomass that will bind to, strip, and help obtain as much of the desirable compounds as possible. However, extraction operators have no solid metric to base their success on, aside from color in sight glasses or laboratory testing. While observing color can be done in-line, it is a subjective metric at best. While lab results are an objective metric, it is nearly impossible to correlate in practice and can take days or even weeks to obtain after a run. While both of these are helpful techniques that should be utilized during the process, they should not be solely relied upon since they lack real-time objectivity. Subjective monitoring that is based on perception or guesswork is imprecise, inconsistent, and difficult to scale. What is the effect of this lack of molecular monitoring during extraction? Batches that are sub-optimally extracted, resulting in either low yields or potency, and even wasted solvents and time. Examples of Applications The most popular applications of the Extraction Finder are hydrocarbon and ethanol extraction. The system can be installed in-line on extractors where there are 1.5” or 2” sanitary flange connections. Multiple units can be placed at multiple points of the extraction design. Hydrocarbon extraction: The unit can be installed in-line between the material column and collection column. Pre-filtration or CRC, the unit’s live data can help you determine what flow rate optimizes both solvated mass & time. Post-filtration or CRC, it can confirm that Chlorophyll is not making it past the filter. Ethanol extraction: The unit can be installed in-line at the recirculation area. It can be used to determine solvent saturation by seeing when the solvent has absorbed the majority of Cannabinoids. The unit is so sensitive that it can even be helpful for confirmation of removal of molecules during a cleaning run.Included in this package:
- Extraction Finder Display
- Extraction Sensor Housing with ultra-sensitive sensor
- Power Supply, with 10′ Extension
- Sensor Cable, 30′
- Pole-Mounting Bracket
- User Manual
- Warranty Card
-
The Short Path Distillation Head Bertha 150, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 150 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 4-6 liters per hour (8 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our MPD heads fit exclusively to Summit MPD boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 150 -
The Short Path Distillation Head Bertha 100, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 100 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 2-4 liters per hour (6 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our flanged heads fit exclusively to Summit MPD boiling flasks: Refer to our instructional (SPD-4 MPD Complete) for correct setup of this head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 100 -
The Cold Trap 2 Shorty (CT-2 Inv Cup Shorty) sets itself apart from others with its patented inverse cup technology. Vapors enter the cup, creating a turbulent vortex, then are forced to condense straight down ensuring proper dry vacuum protection to the pumps. Most traditional traps bypass vapors, only relying on cold surfaces, while this trap prevents nearly all vapors from bypassing. 34/45 female inlet and male outlet. 45/50 flask port. Comes included with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 2 Shorty -
The Cold Trap 2 (CT-2 Inv Cup) sets itself apart from others with its patented inverse cup technology. Vapors enter the cup, creating a turbulent vortex, then are forced to condense straight down ensuring proper dry vacuum protection to the pumps. Most traditional traps bypass vapors, only relying on cold surfaces, while this trap prevents nearly all vapors from bypassing. This trap comes with hard pipe to pumps. 34/45 female inlet and female outlet. 45/50 flask port. Included with: Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distlllation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 2 -
Boiling Flask 22L-3N-71 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) boiling flask. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. This limited edition boiling flask (along with short path distillation head) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. Joints are standard taper 24/40 (2) and 71/60 main. 22 Liter round bottom flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with the Short Path Distillation Head FC71 head. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 22L-3N-71 -
The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo
The condenser in this 150mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm.
Included with this head:
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head 150 -
The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo
The condenser in this 100mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm.
Included with this head:
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Boiling flask not included.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head 100
-
The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo
The condenser in this 55/50 head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm.
45 Key Well, 45 Well Stopper and GL18s (4) included.
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head FC55 -
Premium Schott glass 45/50 key well. 11.25 inch overall length. 6.5 inch length from bottom of the frosted taper with 5 bands. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Head Key Well 45/50 -
Out of stock
Schott glass 45/50 key well. 16.5 inch overall length. 11.5 inch length from bottom of the frosted taper. 10 bands. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. #45 Long Key Well -
$9,630.49
Rebuilt Edwards E2M40 + Blower (mechanical booster) All air cooled dual stage Rotary Vane Pump, 208 V, 50 Hz/208-230 V, 60 Hz/460 V, 60 Hz, Three Phase with KF-40 inlet to blower. Edwards E2M series two stage oil sealed rotary vane vacuum pumps are renowned for their high ultimate vacuum, rapid pumping speeds, quiet operation and ability to handle water vapor. These direct drive rotary vane pumps are inherently compact and vibration free. Blowers add a dimension of vacuum that tops most dual pump options. Mechanical boosters feature the unique hydro-kinetic drive that provides pump down times cut by 50%, when compared with direct drive pumps, no bypass lines or pressure switches required, universal voltage motors, reduced capital and operating costs, air cooled motors – with water cooled options, and quiet, minimum vibration. Operating at relatively low pressures, the mechanical booster pump is not exposed to the same concentrations of corrosive process media as is the backing pump, which makes it highly reliable. Comes with Pump, Blower, MF100 filter and I 19 Standard fluid. To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
The Female to Male Reducer takes a 34/45 female port and reduces to a 24/40 male port. The possibilities with this adapter are endless. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Female to Male Reducer -
The Sensor Ultra Sensitive features the brand new, ultra-sensitive sensor. This package is unique in that - not only does it serve distillation and extraction processes - but also serves Chromatography, Conversion Reaction, and other processes that require more extreme detection. For certain processes, highly sensitive process monitoring is essential. Generally speaking, the more solvent involved in the process means the more sensitive the sensor needs to be. With that in mind, the ULTRA was created. If you are an existing customer, you have the option to upgrade to a standalone ULTRA Sensor for $1,350. Please call us for more details. Use this sensor on any chromatography column with the GL18 to #34 adapter. The Fraction Finder Sensor 34/45 consists of an optical light pulse and detector, acting as “the eyes” of the system. It wraps around a distillation/chromatography setup tube and connects to the Fraction Finder display to track important data on the process.- Fraction Finder optical sensor with ultra-sensitive detector
- Magnetic locking mechanism
- Anodized aluminum apertures
- 90° strap rotation
- Currently only available in size 34mm
- Validated by Arometrix for use on distillation systems
- Currently being tested on reverse-phase chromatography processes
- Display and sight glass not included
Information common with all Fraction Finder sensors
These sensors are black for a reason:- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
The Valved Coil-less Laminar 29 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, GL14 cap and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Coil-less Laminar 29 -
The Valved Coil-less Laminar 34 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, GL14 cap and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Coil-less Laminar 34 -
Laminar No Discharge 29 is a shorter, more compact unit which allows for higher temperatures in the vapor bypass. Coil-less laminar with less turbulence and no discharge. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. Moreover, these short path distillation arms are used in conjunction with a Swing Arm Kit. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar No Discharge 29 -
Laminar No Discharge 34 is a shorter, more compact unit which allows for higher temperatures in the vapor bypass. Coil-less laminar with less turbulence and no discharge. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. Moreover, these short path distillation arms are used in conjunction with a Swing Arm Kit. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar No Discharge 34 -
Dual Female 34 Adapter. Traditional 34/45 taper used to convert male connections together. The possibilities are endless. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Dual Female 34 Adapter -
Adapter fits any KF25 flange with KF25 o-ring and KF25 clamp. Threads are 0.25 inch BSPP. Commonly used for wipers (wiped film or rolling film) using Summit Discharge Pumps. Single adapter only. 100% Billet stainless steel and 100% USA made. -
Boiling Flask 50L-3N-150 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) design. The most popular and strongest short path distillation flask of its kind. Made specifically for Summit MPD flanged heads. Joints are standard taper 24/40 (2) and 150mm main flange. 50 Liter round bottom boiling flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. O-ring and clamp not included (comes with any MPD head) Also available in a smaller size Boiling Flask 22L-3N-150 Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use. We are not responsible or liable for loss of subsequent hardware contamination/failure with or without the result of damaged surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 50L-3N-150 -
The Boiling Flask 22L-3N-150 is made from high quality Schott glass, and is the original Rundkolben (triple offset joints) flask. The most popular and strongest short path distillation flask of its kind. Made specifically for Summit MPD heads. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. Joints are standard taper 24/40 (2) and 150mm main flange. 22 Liter round bottom flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. O-ring and clamp not included (comes with any MPD head) Also available in a larger size Boiling Flask 50L-3N-150 Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use. We are not responsible or liable for loss of subsequent hardware contamination/failure with or without the result of damaged surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 22L-3N-150 -
LN2 stainless steel inverted cup accelerator cold trap. Drier vacuum, lower vacuum and tighter fractions. Extremely compact with higher potency and an over all faster process. We cut the cold trap to show internals in slides 2 & 3. Born from the patented Summit inverse cup cold trap technology and delivered for liquid nitrogen usage. Stainless trap comes with sight glass (essentially a lock off cap) that can be removed and capped off. UPDATED: This SS trap now has 4.75 inch triclamp (4th slide) for many possibilities (liquid nitrogen, dry ice, immersion, sealed immersion, ect.) Included:- 2 inch triclamp Sight glass
- 2 inch triclamp clamps and o-rings
- 2 inch stainless flat cap
- Unit installed with KF25 flanges in and out
- Unit installed with 2 inch triclamp sight glass flange
Clamps, stands and glassware in example picture not included. 4.75 inch triclamp clamp and o-ring not included.
Patented SS Cold Trap Accelerator available only here at Summit Research.
-
The Swing Arm Jacketed Dual Port 34 allows you to swing down for your targeted fraction. That's it. No vacuum break, no changing flasks. 34/45 Throughout. Discharge ports are 29/42. GL14s and Keck Clips included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Swing arm in use at the lab: Instagram Demo
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Swing Arm Jacketed Dual Port 34 -
The Swing Arm Jacketed Dual Port 29 allows you to swing down for your targeted fraction. That's it. No vacuum break, no changing flasks. All ports 29/42. GL14s and Keck Clips included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Swing arm in use at the lab: Instagram Demo
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Swing Arm Jacketed Dual Port 29 -
The Apollo Proportional Vacuum Controller is an advanced scientific laboratory vacuum controller, display, digital readout, and vacuum live reading analysis device. This version of the Apollo can service up to FOUR REMOTE vacuum sensors of any kind with up to FOUR REMOTE vacuum valves that are controlled by the Digi-Vac dinamo proportional live CFM control valve. KF25 flanges, barbed breather valve. This device is essential for high speed rotary evaporation control and crucial for controlling and even increasing recovery rates on falling film evaporation machines. Those might be the top two, but the possibilities are rising with new tech that have KF25 fitment. The device has a continuous CFM open-close valve that never actually stops moving. Typically it will not close but the effect is reached with the ability to increase or decrease CFM size allowing to maintain vacuum select point control. If the set point comes up, it will close the valve. If the set point goes down it will open the valve. Typically very minute movements inside make a huge performance difference and increase in vacuum pump performance allowing continual cfm-to-micron control. This Apollo controller can be expanded but comes with ONE EXTERNAL COUPLED device standard. This is an Apollo brain unit with a chemical duty touch screen, with remote valve/sensor. Standard options are as follows:- The first board location is equipped by summit with one sensor designed for aggressive solvent use and one proportional valve (dinamo valve).
- Three more slots are available to accept up to three more sensors and three more valves.
- The additional optional upgrade is only several hundred dollars for each additional proportional valve control added-on. any length cable can be used, please inform us for a specialty need with longer cables than what is supplied.
-
50 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 50 liter kit, and a link for you to check them out in detail:- SPD Head FC71
- Genesis Mantle
- Boiling Flask 50L-3N-71
- Laminar Path Monocow 34
- Receiving Flask 29 3 Liter (2)
- Receiving Flask 29 5 Liter (2)
- Receiving Flask 29 12 Liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29
- Keck Clip 34 (5)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- High Temp GL14 (4)
- Appropriate key well 34
-
Summit 4x48 Filter Column Complete comes with 2 stainless columns and complete rack and pump. 2 sets of sintered discs (16 total) (varying sizes) included. Swagelok valves. Stainless steel. Made in USA. Call us for more columns and fill your rack!
-
$12,500.00
A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.Benefits
Important characteristics
-
All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here:To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
-
-
$13,500.00
A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.Benefits
Important characteristics
Performance Data Temperature Heating-up time to 100 °C [min] 80 Temperature fluctuation [± K] 0.1 Temperature range 15 °C above ambient temperature to [°C] 200 Temperature variation at 100 °C [± K] 2 Vacuum Data Leak rate [bar/h] 0.01 Permitted end vacuum [mbar] 0.01 Electrical data Nominal power [kW] 1.2 Phase (Nominal voltage) 1~ Power frequency [Hz] 50/60 Rated Voltage [V] 230 Unit fuse [A] 10 Connections Compressed air connection for pressure-encapsulation 8 mm Inert gas connection with flow limiter (RP") 3/8 Measuring access port with small flange [DN mm] 16 Vacuum connection with small flange [DN mm] 16 Housing dimensions not incl. fittings and connections Depth net [in] 21.67 Height net [in] 30.53 Width net [in] 25.02 Internal Dimensions Depth [in] 13.4 Height [in] 15.76 Width [in] 15.76 Measures Interior volume [cu.ft.] 1.9 Load per rack [lbs] 44 Net weight of the unit (empty) [lbs] 209 Permitted load [lbs] 99 Viewing window height [in] 12.1 Viewing window width [in] 13.79 Wall clearance back [in] 3.94 Wall clearance sidewise [in] 5.32 Fixtures Number of shelves (std./max.) 2/5 Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here:-
All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
-
$17,500.00
A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.Benefits
Important characteristics
Performance Data Temperature Heating-up time to 100 °C [min] 95 Temperature fluctuation [± K] 0.1 Temperature range 15 °C above ambient temperature to [°C] 200 Temperature variation at 100 °C [± K] 3.5 Vacuum Data Leak rate [bar/h] 0.01 Permitted end vacuum [mbar] 0.01 Electrical data Nominal power [kW] 1.9 Phase (Nominal voltage) 1~ Power frequency [Hz] 50/60 Rated Voltage [V] 230 Unit fuse [A] 10 Connections Compressed air connection for pressure-encapsulation 8 mm Inert gas connection with flow limiter (RP") 3/8 Measuring access port with small flange [DN mm] 16 Vacuum connection with small flange [DN mm] 16 Housing dimensions not incl. fittings and connections Depth net [in] 26.4 Height net [in] 35.46 Width net [in] 29.16 Internal Dimensions Depth [in] 18.12 Height [in] 19.94 Width [in] 19.94 Measures Interior volume [cu.ft.] 4.1 Load per rack [lbs] 44 Net weight of the unit (empty) [lbs] 337 Permitted load [lbs] 143 Viewing window height [in] 16.27 Viewing window width [in] 17.97 Wall clearance back [in] 3.94 Wall clearance sidewise [in] 5.32 Fixtures Number of shelves (std./max.) 2/6 Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here:-
All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
-
Laminar Coil-less 29 is a shorter, more compact short path distillation arm which allows for higher temperatures in the vapor bypass. A true laminar with less turbulence. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar Coil-less 29 -
Laminar Coil-less 34 is a shorter, more compact short path distillation arm which allows for higher temperatures in the vapor bypass. A true laminar with less turbulence. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar Coil-less 34 -
$14,285.00
Polyscience 3HP Heavy Duty Durachill will handle numerous tasks. Air cooled with simple operation and maintenance. When precision liquid cooling matters, go with Polyscience cooling solutions.To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.- DuraChill® Chillers 2HP and up are not available outside of the United States
- High capacity cooling for plasma torch cutting, machine tool hydraulics, high powered lasers, and other high heat generating processes and equipment
- Displays temperature and pressure or flow rate simultaneously
- User-adjustable temperature, pressure, and flow rate alarms
- Simple operation and maintenance
- Wide variety of options available
-
$17,995.00
Polyscience 8HP Heavy Duty Air Cooled 3 Phase Chiller will handle different tasks - 50L roto rating. When precision liquid cooling matters, go with Polyscience cooling solutions.To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.- DuraChill® Chillers 2HP and up are not available outside of the United States
- High capacity cooling for plasma torch cutting, machine tool hydraulics, high powered lasers, and other high heat generating processes and equipment
- Displays temperature and pressure or flow rate simultaneously
- User-adjustable temperature, pressure, and flow rate alarms
- Simple operation and maintenance
- Wide variety of options available
-
$21,995.00
Polyscience 5HP Heavy Duty 3 Phase Chiller will handle different tasks - 50L roto rating. When precision liquid cooling matters, go with Polyscience cooling solutions.To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.- DuraChill® Chillers 2HP and up are not available outside of the United States
- High capacity cooling for plasma torch cutting, machine tool hydraulics, high powered lasers, and other high heat generating processes and equipment
- Displays temperature and pressure or flow rate simultaneously
- User-adjustable temperature, pressure, and flow rate alarms
- Simple operation and maintenance
- Wide variety of options available
-
$21,995.00
Polyscience Heavy Duty 10HP 3 Phase Chiller will handle different tasks - dual 50L roto rating. When precision liquid cooling matters, go with Polyscience cooling solutions.To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.- DuraChill® Chillers 2HP and up are not available outside of the United States
- High capacity cooling for reactors
- Displays temperature and pressure or flow rate simultaneously
- User-adjustable temperature, pressure, and flow rate alarms
- Simple operation and maintenance
- Wide variety of options available
-
Fits Size 29 or 34 Fraction Finder Sensor (drop down menu) Details:- Goes in-line between the condenser & collection flask, allowing you to use the Fraction Finder in a new location and still run a hot condenser.
- High temperatures can be problematic for our sensor; this relocates where Fraction Finder could be positioned.
- Watch this video to see how it works.
-
The Valved Laminar Path 29 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, (3) GL14s (1 cap) and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Laminar Path 29 -
The Valved Laminar Path 34 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, (3) GL14s (1 cap) and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Laminar Path 34 -
Liquid Temp Control Key 34/45 is a short path distillation head key that is used to generate a localized cold/hot surface. The temperature achieved reduces or enlarges the quantity of volatile material exhausted into the air. This premium Schott glass 34mm plug is 8.5 inch overall length and 4.5 inch from the bottom of the frosted taper with the tip being a small condenser coil. High Temp GL14s included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Liquid Temp Control Key 34/45 -
When the going gets tough, you can't ever be too safe! A triple coil intermediate trap with female 34/45 inlet and male outlet. This trapping mechanism is used as a laminar path connection recommended for larger short path distillation setups (22-50L) leading into dual cold traps. Heavy wall and joint thickness. Upgraded GL18 connections prevent barb breakage and mass body failure from stress of removing hoses. Extreme duty capacity and redesigned custom sized parallel flow coils that supply you with unmatched cooling. Collection flask port 45/50. Comes complete with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 3 Shorty -
Liquid Temp Control Key 45/50 is a short path distillation head key that is used to generate a localized cold/hot surface. The temperature achieved reduces or enlarges the quantity of volatile material exhausted into the air. This premium Schott glass 45mm plug is 14.25 inch overall length and 10.5 inch from the bottom of the frosted taper with 4 large bands. High Temp GL14s included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Liquid Temp Control Key 45/50 -
$14,095.00
Specifications- Type of Product: Scroll Pump
- Manufacturer: Edwards
- Condition: New
- Part Number: A73001983
- Inlet: KF40
- Exhaust: KF25
- Motor: 1 Phase, 100-120/200-230V, 50/60Hz
- Pumping speed: 21 CFM
- Ultimate vacuum: 8 x 10-3 Torr
- Weight: 105 lbs
- closed loop temperature monitoring
- dry, clean vacuum free of lubricants
- simple, single-sided scroll design
- patented isolated bearing shield
- world-wide voltage compatibility
- low power consumption
- controllable gas ballast
- inverter driven motor
-
$7,117.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF25
- Exhaust: KF16
- Motor: 1 Phase, 100-115/220-230V, 50/60Hz
- Pumping speed: 7.53 CFM (50Hz), 9.06 CFM (60Hz)
- Ultimate pressure: 1 x 10-2 Torr
- Weight: 75 lbs
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$5,490.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF25
- Exhaust: KF16
- Motor: 1 Phase, 100-120/200-240V, 50/60Hz
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$5,164.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF25
- Exhaust: KF16
- Motor: 1 Phase, 100-120/200-240V, 50/60Hz
- Pumping speed: 4.23 CFM (50Hz), 5.35 CFM (60Hz)
- Ultimate pressure: 3 x 10-2 Torr (50Hz), 2 x 10-2 Torr (60Hz)
- Weight: 54 lbs
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$2,977.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF16
- Exhaust: 1/4" FNPT
- Motor: 1 Phase, 115V, 60Hz
- Pumping speed: 1.76 CFM (50Hz), 2.11 CFM (60Hz)
- Ultimate pressure: 2.5 x 10-1 Torr
- Weight: 21 lbs
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- At only 21 pounds (9.5 kg), IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
Chroma Column FF 6x48 with coarse/fine mixed frit and heavy wall thickness of 3mm. Special design allows for #29 Fraction Finder that permits you to check your fraction and watch your progression. Attach a FF between the frit and the stopcock area. Comes with rodaviss , GL18 and #45 Chroma Cap. Fraction Finder not included. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! Please use this column at your own risk! In addition to lab stands, it is recommended that you secure the lab stands to a wall or sturdy foundation while also using sandbags. This column will surpass 100+ lbs of weight holding full fluid. Please make sure you are offsetting the weight of your fluids. Summit requires this chromatography column to be supported by 3 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not included) to maximize grip. This column may slip though clamps if not properly bottom supported. Recommended (yet again), to have a lab tripod base (use rubber stripping here as well) or a circular clamp about 5" diameter (not included)(last picture). The Chroma Column FF 6x48 has no warranty. https://www.instagram.com/p/B5Lv5CzBAS-/ As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's. Stands, clamps, sandbag and Fraction Finder are not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chroma Column FF 6x48 -
The Short Path Distillation Head FC71 includes a 71/60 main bore with a 34/45 discharge and 34/45 thermoport. The 71 mm can handle bigger systems and a lot of product. A very versatile head that we can cater towards your needs. Comes with 34 key, 34 stopper well and GL14s. This limited edition short path distillation head (along with boiling flask) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with these boiling flasks: Summit has 5L and 12L options for this head. Please call us for more information. Clamp and stands not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC71 -
PLEASE CALL FOR AVAILABILITY. HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB2 150 comes equipped with 45/50 key port, 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB2 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB2 is designed to be ultra high speed with precision refinement. This head was bench marked by Heisenberg on a dual e2m30 array achieving 6 liters per hour without any effort at all. This head can be setup for very low temperatures, high clarity, and high speeds. Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. The HB2 150mm head comes included with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. -
HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB1 150 comes equipped with 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB1 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB1 is designed to be ultra selective to evacuate all previous fractions before the main body without letting the main body through. With some temp, main body can come out extremely fast and this head can be used as a first pass head. It is very effective in removing heads fractions while retaining main body components. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Please contact us for a completely tuned system with this hardware! Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. The HB1 150mm head comes with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. -
Boiling Flask 50L-3N-71 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) design. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. This limited edition boiling flask (along with short path distillation head) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. Joints are standard taper 24/40 (2) and 71/60 main. 50 Liter round bottom boiling flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with the Short Path Distillation Head FC71 head. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. RBF 50L-3N-71
-
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail: Parts: The Summit research spd-7/7.1 USPD systems are designed to fully refine products at a low temperature; preferred material required should be refined previously, or physically refined through all filtration and washing/chroma processes. Stands, crossbars and clamps sold separately. -
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail: Parts: The Summit research spd-7/7.1 USPD systems are designed to fully refine products at a low temperature; preferred material required should be refined previously, or physically refined through all filtration and washing/chroma processes. Stands, crossbars and clamps sold separately. -
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. 22 Liter assembly: Instagram Demo
Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.
- Head choice: SPD-6 Tall / SPD-6 Shorty / SPD-6 Nano
- Genesis Mantle
- Boiling Flask 22L-3N-55
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 liter (2)
- Receiving Flask 29 5 liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (4)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- High Temp GL14 (4)
- Appropriate key for your head choice
-
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Head choice: SPD-6 Tall / SPD-6 Shorty / SPD-6 Nano
- Genesis Mantle
- Boiling Flask 12L-3N-55
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 liter (2)
- Receiving Flask 29 5 liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (4)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- GL14 (4)
- Appropriate key for your head choice
-
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantle and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Choice of Head: SPD-6 FC45 Tall / SPD-6 FC45 Shorty / SPD-6 FC45 Nano
- Genesis Mantle
- Boiling Flask 12L-3N-45
- Laminar Path Monocow 29
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 liter (2)
- Receiving Flask 29 5 liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (4)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- GL14 (4)
- Appropriate key for head selection
-
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantle and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Head choice: SPD-6 FC45 Tall / SPD-6 FC45 Shorty / SPD-6 FC45 Nano
- Genesis Mantle
- Boiling Flask 5L-3N-45
- Laminar Path Monocow 29
- Receiving Flask 29 1 Liter (2)
- Receiving Flask 29 2 liter (2)
- Receiving Flask 29 3 liter (2)
- Cold Trap 1 34 to GL
- Swage DV-2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34
- Stopper 24 (2)
- Rare Earth PTFE Pill 24x50mm
- Rodaviss kit
- GL14 (4)
- GL18 (2)
- GL18 Lock off cap
- Appropriate key head selection
-
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantle and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail:- Choice of Head: SPD-6 FC45 Tall / SPD-6 FC45 Shorty / SPD-6 FC45 Nano
- Genesis Mantle
- Boiling Flask 5L-3N-45
- Laminar Path Monocow 29
- Receiving Flask 29 1 Liter (2)
- Receiving Flask 29 2 liter (2)
- Receiving Flask 29 3 liter (2)
- Cold Trap 2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (3)
- Stopper 24 (2)
- Rare Earth PTFE Pill 24x50mm
- Rodaviss kit
- GL14 (4)
- Appropriate key for head selection
-
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail:- SPD Head Bertha 100
- Genesis Mantle
- Boiling Flask 22L-3N-100
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 Liter (2)
- Receiving Flask 29 5 Liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29
- Keck Clip 34 (5)
- Stopper 24 (2)
- Stopper Well 34
- Head Key Well 10 Band 34
- Head Key 21 Band 34
- Rare Earth PTFE Pill 28x70mm
- Rodaviss Kit (2)
- High Temp GL14 (4)
- PTFE O-Ring 100mm
- Flange Clamp 100mm
-
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail:- SPD Head Bertha 100
- Genesis Mantle
- Boiling Flask 12L-3N-100
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 Liter (2)
- Receiving Flask 29 5 Liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29
- Keck Clip 34 (5)
- Stopper 24 (2)
- Stopper Well 34
- Head Key Well 10 Band 34
- Head Key 21 Band 34
- Rare Earth PTFE Pill 28x70mm
- Rodaviss Kit (2)
- High Temp GL14 (4)
- PTFE O-Ring 100mm
- Flange Clamp 100mm
-
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail: Parts: This 22 Liter HB Package comes with two heads. The HB1 head has a built in key with heavy knock down and refinement with high speed. The HB2 head has a general theoretical plate at the bottom with a mean free pathway at top that includes a modified path distillation pathway. Combined with removable key, this head is your precision refiner. Stands, crossbars and clamps sold separately. -
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail: Parts: This 12 Liter HB Package comes with two heads. The HB1 head has a built in key with heavy knock down and refinement with high speed. The HB2 head has a general theoretical plate at the bottom with a mean free pathway at top that includes a modified path distillation pathway. Combined with removable key, this head is your precision refiner. Stands, crossbars and clamps sold separately. -
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail: Parts: This 5 Liter HB Package comes with two heads. The HB1 head has a built in key with heavy knock down and refinement with high speed. The HB2 head has a general theoretical plate at the bottom with a mean free pathway at top that includes a modified path distillation pathway. Combined with removable key, this head is your precision refiner. Stands, crossbars and clamps sold separately. -
2 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 2 liter kit, and a link for you to check them out in detail:- Short Path Distillation Head FC34
- Genesis Mantle
- Boiling Flask 2 Liter 24/24/34
- Laminar Path Monocow 29
- Receiving Flask 29 500ml (2)
- Receiving Flask 29 1 Liter (2)
- Cold Trap 1 34 to GL
- DV-2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34
- Stopper 24 (2)
- Well Stopper 24
- Short Key 24
- Rare Earth PTFE Pill 14x25mm
- Rodaviss Kit
- GL14 (4)
- GL18 (2)
- GL18 Lock Off Cap
-
2 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 2 liter kit, and a link for you to check them out in detail:- Short Path Distillation Head FC34
- Genesis Mantle
- Boiling Flask 2 Liter 24/24/34
- Laminar Path Monocow 29
- Receiving Flask 29 500ml (2)
- Receiving Flask 29 1 Liter (2)
- Cold Trap 2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Hard Pipe for Cold Trap
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (3)
- Stopper 24 (2)
- Well Stopper 24
- Short Key 24
- Rare Earth PTFE Pill 14x25mm
- Rodaviss Kit
- GL14 (4)
-
Sale!
Premium Schott glass 24/40 plug. 5.5 inch overall length thermowell. 2 inch length from bottom of the frosted taper. Allows for accurate thermometer readings in the head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Well Stopper 24/40 -
Premium Schott glass 34/45 plug. 7.75 inch overall length thermowell. 3 inch length from bottom of the frosted taper. Allows for accurate thermometer readings in the head while allowing zero rejection compared to a key with bands. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Well Stopper 34/45 -
Premium Schott glass 45/50 well stopper. 4.75 inch length from bottom of the frosted taper. 9.5 inch overall length. Allows for accurate thermometer readings in the head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Well Stopper 45/50 -
$12,000.00 $9,990.00
Second to none in temperature uniformity, temperature stability and drying speed (purging). The combination of these high marks results in throughput (yield & productivity). This unit reaches 100°F in just 15 minutes thanks to the individual direct shelf heating. Each shelf has its own temperature controller for varying temperatures. KF25 full bore into the oven all the way to the chamber. No size reductions like in other ovens. These ovens are the real deal. CE & UL CERTIFIED! 9cu ft Vacuum oven specificationsElectric 110V 50/60Hz 1PH 13.6A, 1500W Chamber Size: 15.75 x 15 x 23" deep Material: Stainless Steel Capacity: 9 cubic feet Temperature control Controller: microcomputer with LCD display Range: ambient to 302°F Display units: Fahrenheit or Celsius Accuracy: +/- 0.1°F Uniformity: +/- 0.5 at 100°F5 Controllers (individual direct shelf heating)Warm-up time to 100°F: 15 minutes (without load) Vacuum Range: 0 to 76 cmHg (0 to 0.1MPa) Vacuum port: KF25 flange x1, KF25 strait pipe with elbow x1, KF25 clamps and o-rings x2 (ALL INCLUDED)Vent port: 3/8" female threaded Weight Unit: 555 Lbs, shipping: 747 Lbs Dimensions (WxDxH) Unit: 38 x 37 x 32" Shipping: 45 x 45 x 44" Shelves 5 fixed and individually heated shelves, 23x27" each Distance between shelves: 4"Area: 23x27" , 345 sq inches Door gasket material Food grade silicone Observation window 3/4" tempered glass Safety Built in circuit breaker, over-temp protector In-door lights LED CE & UL compliance Yes
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$5,000.00 $4,490.00
Second to none in temperature uniformity, temperature stability and drying speed (purging). The combination of these high marks results in throughput (yield & productivity). KF25 full bore into the oven all the way to the chamber. No size reductions like in other ovens. These ovens are the real deal. CE & UL CERTIFIED! 3.4 cu ft Vacuum oven specificationsElectric 110V 50/60Hz 1PH 12.3A, 1350W Chamber Size: 15.75 x 15 x 23" deep Material: Stainless Steel Capacity: 3.4 cubic feet Temperature control Controller: microcomputer with LCD display Range: ambient to 302°F Display units: Fahrenheit or Celsius Accuracy: +/- 0.1°F Uniformity: +/- 0.5 at 100°F1 ControllerWarm-up time to 100°F: 40 minutes (without load) Vacuum Range: 0 to 76 cmHg (0 to 0.1MPa) Vacuum port: KF25 flange x1, KF25 strait pipe with elbow x1, KF25 clamps and o-rings x2 (ALL INCLUDED) Vent port: 3/8" female threaded Weight Unit: 255 Lbs, shipping: 423 Lbs Dimensions (WxDxH) Unit: 35 x 32 x 28" Shipping: 42 x 39 x 39" Shelves 10 removable shelves, 15 x 23" (WxD) each Distance between shelves: 1.5"Area: 15x23" , 345 sq inches Door gasket material Food grade silicone Observation window 3/5" tempered glass Safety Built-in circuit breaker, over-temp protector In-door lights LED CE & UL compliance Yes
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
The Fraction Finder Sensor #34 consists of an optical light pulse and detector, acting as “the eyes” of the system. It wraps around a distillation set up condenser tube and connects to the Fraction Finder display to track important data on the distillation. These sensors are black for a reason:- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
The Fraction Finder Sensor #29 consists of an optical light pulse and detector, acting as “the eyes” of the system. It wraps around a distillation set up condenser tube and connects to the Fraction Finder display to track important data on the distillation. These sensors are black for a reason:- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
Fits Size 29 Fraction Finder Sensor Details:- 29/42 Rodaviss male to female adapter with 28mm 1.5″ section for Size 29 Fraction Finder Sensor
- 29/42 Rodaviss kit/smaller parts with cap, O-ring, and loosening ring
-
Fits Size 29 Fraction Finder Sensor Details:- 1L teardrop/recovery flask with Rodaviss 29/42 connection with extended neck with 28mm O.D.
-
From: $8,450.00
Interfaces any centrifuge extractor that doesn't require C1D2 (ethanol, heptane, methanol, etc.) with the size 34 Fraction Finder sensor.Sight Glass for Ethanol Extraction – includes shield and modified size 34 sensor- 1.5″ or 2" Sanitary flange sight glass with shield and a modified sensor (includes sensor pre-installed, evacuation/purge cycle, vacuum and pressure tested, sensor tested, and 10′ cable)
- Fraction Finder sensor included and pre-installed
- For use with an ethanol extractor
