-
$4,999.99
The new SPD-8 Series Heads (FC55, 60mm, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. This 2 liter head comes with boiling flask! Can be upgraded to 5 liter flask, please call us. Short Path Distillation 8 Head in use at the lab: Instagram Demo The condenser in this 60mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head:- Head Key Well 45/50
- Stopper Well 45/50
- High Temp GL18s (4)
- Flange Clamp 60mm
- PTFE O-Ring 60mm
- 2 Liter Boiling Flask
-
The KF16 to Male 24/40 PTFE Adapter is typically used to convert a glass system to a vacuum system or sensor. Adapter has 11mm bore. Secure your male connection with a keck clip. PTFE billet parts made right here in the USA. Be sure to have KF16x10 Centering Ring and KF16 clamp to make your KF16 connection.
-
The KF40 Bellow is a corrugated stainless steel pipe that connects to corresponding kf40 flanges. These malleable pipes allow for some error as apposed to hooking up a solid straight pipe. Available in 24 and 36 inch lengths. Don't forget other KF40 fittings and accessories: 100% stainless steel. 100% USA made. Bellow warning: Stretch and bend your bellow into position before installation. Engaging your pump(s) while not doing so could make the bellow jolt/jostle, putting stress on or damage glassware, voiding limited warranties. KF40 Bellow
-
The Flange Adapter 100mm is used to convert a flanged 100mm boiling flask to a 55mm (55/50) standard taper. You could utilize a different head or use a reflux condenser, the possibilities are endless. Glass unit only, clamp and O-ring not included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Flange Adapter 100mm
-
The Fraction Finder Ultra Sensitive figures out where components start and stop flowing to optimize separation. Making the SPD Process more precise and repeatable, Fraction Finding helps take the guess work out. Someone running a distillation can make better decisions if they knew exactly where they were in the distillation process. Scientists have developed expertise in this area to the point where they know what to expect. The Summit Research Fraction Finder does that for you and will be your best friend in short path distillation. Included with:
- Ultra Sensitive sensor
- Mounting hardware
- Display screen
- Light-blocking tape
- Power Supply
- Sensor Cable
- User Manual and Quick Start Guide
- 1-Year Warranty
- Fraction Finder optical sensor with ultra-sensitive detector
- Magnetic locking mechanism
- Anodized aluminum apertures
- 90° strap rotation
- Currently only available in size 34
- Validated by Arometrix for use on distillation systems
- Currently being tested on reverse-phase chromatography processes
- Display and sight glass not included
Information common with all Fraction Finder sensors
These sensors are black for a reason:- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
Cold Trap 2 Hard Pipe with male 34/45 (from cold trap) and 34/45 female exit (to pumps). The straight pipe acts as a sight glass and is a great last line of defense to see if any moisture is reaching your pumps. Total length: 24.5 inches and 3.5 inches at top section. Hard pipe only, cold trap not included. Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distillation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. CT-2 Hard Pipe
-
$4,849.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 150mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 150mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 150 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$5,224.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 150mm clamp with O-ring and PTFE GL18s (4) included. 45/50 Key port and appropriate key & well stopper. 34/45 discharge port. Our 150mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 150 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$4,499.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 100mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 100mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 100 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$4,299.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 34/45 key, 100mm clamp with O-ring and PTFE GL18s (4) included. 34/45 discharge port. Our 100mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 100 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
The Short Path Distillation Head Bertha 150, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 150 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 4-6 liters per hour (8 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our MPD heads fit exclusively to Summit MPD boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 150
-
The Short Path Distillation Head Bertha 100, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 100 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 2-4 liters per hour (6 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our flanged heads fit exclusively to Summit MPD boiling flasks: Refer to our instructional (SPD-4 MPD Complete) for correct setup of this head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 100
-
The Cold Trap 2 Shorty (CT-2 Inv Cup Shorty) sets itself apart from others with its patented inverse cup technology. Vapors enter the cup, creating a turbulent vortex, then are forced to condense straight down ensuring proper dry vacuum protection to the pumps. Most traditional traps bypass vapors, only relying on cold surfaces, while this trap prevents nearly all vapors from bypassing. 34/45 female inlet and male outlet. 45/50 flask port. Comes included with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 2 Shorty
-
The Cold Trap 2 (CT-2 Inv Cup) sets itself apart from others with its patented inverse cup technology. Vapors enter the cup, creating a turbulent vortex, then are forced to condense straight down ensuring proper dry vacuum protection to the pumps. Most traditional traps bypass vapors, only relying on cold surfaces, while this trap prevents nearly all vapors from bypassing. This trap comes with hard pipe to pumps. 34/45 female inlet and female outlet. 45/50 flask port. Included with: Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distlllation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 2
-
Boiling Flask 22L-3N-71 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) boiling flask. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. This limited edition boiling flask (along with short path distillation head) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. Joints are standard taper 24/40 (2) and 71/60 main. 22 Liter round bottom flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with the Short Path Distillation Head FC71 head. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 22L-3N-71
-
The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo The condenser in this 150mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head 150
-
The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo The condenser in this 100mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Boiling flask not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head 100
-
The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo The condenser in this 55/50 head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. 45 Key Well, 45 Well Stopper and GL18s (4) included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head FC55
-
The Flange Clamp 150mm attaches to any 150mm MPD setup. The PTFE O-Ring 150mm is required to make the seal. Clamp and O-Ring come included with any MPD head. Boiling Flask applications:
-
The Flange Clamp 100mm attaches to any 100mm MPD setup. The PTFE O-Ring 100mm is required to make the seal. Clamp and O-Ring come with any MPD head. Boiling Flask applications:
-
Premium Schott glass 45/50 key well. 11.25 inch overall length. 6.5 inch length from bottom of the frosted taper with 5 bands. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Head Key Well 45/50
-
Reflux condensers are used in “conversion” processes to cool the vapor molecules emitted from heated oils to change their gaseous state back into liquid by means of a chilled dual coil. This unit is recommended for 12L and smaller boiling flasks. How it works: The condenser is attached to the boiling flask joint and is secured in a vertical position. Chiller fluid is circulated through the coil to cause the vapors to condense as they rise up through the condenser coils thus preventing them from escaping. This gives you the option to reflux different fluids in your boiling flask for extended periods of time before you run the SPD, this is a must have in the lab for conversions. Flask entry port is 55/50 with 24/40 exit port. Total dimensions 25.75 x 2.25 inch. High Temp GLs included. 24/40 to GL14 Adapter OR 24/40 to GL18 Adapter included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. NEED A 34/45 PORT? Call us, you can custom order anything! Base not included Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Reflux Condenser Dual Coil
-
Reflux condensers are used in “conversion” processes to cool the vapor molecules emitted from heated oils to change their gaseous state back into liquid by means of a chilled triple coil. This unit is recommended for 22L and larger boiling flasks. How it works: The condenser is attached to the boiling flask joint and is secured in a vertical position. Chiller fluid is circulated through the coil to cause the vapors to condense as they rise up through the condenser coils thus preventing them from escaping. This gives you the option to reflux different fluids in your boiling flask for extended periods of time before you run the SPD, this is a must have in the lab for conversions. Flask entry port is 55/50 with 24/40 exit port. High Temp GLs included. 24/40 to GL14 Adapter OR 24/40 to GL18 Adapter included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. NEED A 45/50 PORT? Call us, you can custom order anything! Base not included Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Reflux Condenser Triple Coil
-
The Female to Male Reducer takes a 34/45 female port and reduces to a 24/40 male port. The possibilities with this adapter are endless. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Female to Male Reducer
-
The Sensor Ultra Sensitive features the brand new, ultra-sensitive sensor. This package is unique in that - not only does it serve distillation and extraction processes - but also serves Chromatography, Conversion Reaction, and other processes that require more extreme detection. For certain processes, highly sensitive process monitoring is essential. Generally speaking, the more solvent involved in the process means the more sensitive the sensor needs to be. With that in mind, the ULTRA was created. If you are an existing customer, you have the option to upgrade to a standalone ULTRA Sensor for $1,350. Please call us for more details. Use this sensor on any chromatography column with the GL18 to #34 adapter. The Fraction Finder Sensor 34/45 consists of an optical light pulse and detector, acting as “the eyes” of the system. It wraps around a distillation/chromatography setup tube and connects to the Fraction Finder display to track important data on the process.
- Fraction Finder optical sensor with ultra-sensitive detector
- Magnetic locking mechanism
- Anodized aluminum apertures
- 90° strap rotation
- Currently only available in size 34mm
- Validated by Arometrix for use on distillation systems
- Currently being tested on reverse-phase chromatography processes
- Display and sight glass not included
Information common with all Fraction Finder sensors
These sensors are black for a reason:- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
The Valved Coil-less Laminar 29 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, GL14 cap and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Coil-less Laminar 29
-
The Valved Coil-less Laminar 34 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, GL14 cap and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Coil-less Laminar 34
-
Laminar No Discharge 29 is a shorter, more compact unit which allows for higher temperatures in the vapor bypass. Coil-less laminar with less turbulence and no discharge. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. Moreover, these short path distillation arms are used in conjunction with a Swing Arm Kit. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar No Discharge 29
-
Laminar No Discharge 34 is a shorter, more compact unit which allows for higher temperatures in the vapor bypass. Coil-less laminar with less turbulence and no discharge. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. Moreover, these short path distillation arms are used in conjunction with a Swing Arm Kit. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar No Discharge 34
-
Dual Female 34 Adapter. Traditional 34/45 taper used to convert male connections together. The possibilities are endless. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Dual Female 34 Adapter
-
Adapter fits any KF25 flange with KF25 o-ring and KF25 clamp. Threads are 0.25 inch BSPP. Commonly used for wipers (wiped film or rolling film) using Summit Discharge Pumps. Single adapter only. 100% Billet stainless steel and 100% USA made.
-
Boiling Flask 50L-3N-150 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) design. The most popular and strongest short path distillation flask of its kind. Made specifically for Summit MPD flanged heads. Joints are standard taper 24/40 (2) and 150mm main flange. 50 Liter round bottom boiling flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. O-ring and clamp not included (comes with any MPD head) Also available in a smaller size Boiling Flask 22L-3N-150 Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use. We are not responsible or liable for loss of subsequent hardware contamination/failure with or without the result of damaged surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 50L-3N-150
-
The Boiling Flask 22L-3N-150 is made from high quality Schott glass, and is the original Rundkolben (triple offset joints) flask. The most popular and strongest short path distillation flask of its kind. Made specifically for Summit MPD heads. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. Joints are standard taper 24/40 (2) and 150mm main flange. 22 Liter round bottom flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. O-ring and clamp not included (comes with any MPD head) Also available in a larger size Boiling Flask 50L-3N-150 Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use. We are not responsible or liable for loss of subsequent hardware contamination/failure with or without the result of damaged surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 22L-3N-150
-
Pressurized fluid and solution stainless steel handling keg. 2 inch diameter tri-clamp. Full chemical duty. Choice of 5 gallon or 15 gallon. Whether running hot or cold, pressurized or not, these durable kegs get the job done. Made in USA. Comes with clamp, o-ring, two port lid and 3/8 nipples. Keg measures 26inches x 15.5inches.
-
Pressurized fluid and solution stainless steel handling keg. 2 inch diameter tri-clamp. Full chemical duty. Choice of 5 gallon or 15 gallon. Whether running hot or cold, pressurized or not, these durable kegs get the job done. Made in USA. Comes with clamp, o-ring, two port lid and 3/8 nipples. Keg measures 26inches x 9inches.
-
The Swing Arm Jacketed Dual Port 34 allows you to swing down for your targeted fraction. That's it. No vacuum break, no changing flasks. 34/45 Throughout. Discharge ports are 29/42. GL14s and Keck Clips included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Swing arm in use at the lab: Instagram Demo Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Swing Arm Jacketed Dual Port 34
-
The Swing Arm Jacketed Dual Port 29 allows you to swing down for your targeted fraction. That's it. No vacuum break, no changing flasks. All ports 29/42. GL14s and Keck Clips included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Swing arm in use at the lab: Instagram Demo Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Swing Arm Jacketed Dual Port 29
-
The Filter Bottle 20 Liter is genuine thick Schott glass media. We spared no cost to have our shop mount the bottle on a lathe and remove the bung section, replacing it with a Rodaviss female end. These flawless HEAVY DUTY glass filtration bottles are one of kind and come with Rodaviss wet-seal parts, Filter Bottle Top and High Temp PTFE GL14 connections. THIS ITEM DOES NOT HAVE A WARRANTY AND SHOULD BE TREATED WITH CARE ON A RUBBER MAT, WITHOUT OVER TIGHTENING THE TOP. RETURNS FOR DAMAGED BOTTLES WILL BE REFUSED UNCONDITIONALLY. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve for your filtration process's. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Filter Bottle 20 Liter
-
The Filter Bottle 10 Liter is genuine thick Schott glass media. We spared no cost to have our shop mount the bottle on a lathe and remove the bung section, replacing it with a Rodaviss female end. These flawless HEAVY DUTY glass filtration bottles are one of kind and come with Rodaviss wet-seal parts, Filter Bottle Top and High Temp PTFE GL14 connections. THIS ITEM DOES NOT HAVE A WARRANTY AND SHOULD BE TREATED WITH CARE ON A RUBBER MAT, WITHOUT OVER TIGHTENING THE TOP. RETURNS FOR DAMAGED BOTTLES WILL BE REFUSED UNCONDITIONALLY. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve for your filtration process's. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. 10L Filter Bottle
-
50 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 50 liter kit, and a link for you to check them out in detail:- SPD Head FC71
- Genesis Mantle
- Boiling Flask 50L-3N-71
- Laminar Path Monocow 34
- Receiving Flask 29 3 Liter (2)
- Receiving Flask 29 5 Liter (2)
- Receiving Flask 29 12 Liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29
- Keck Clip 34 (5)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- High Temp GL14 (4)
- Appropriate key well 34
-
Laminar Coil-less 29 is a shorter, more compact short path distillation arm which allows for higher temperatures in the vapor bypass. A true laminar with less turbulence. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar Coil-less 29
-
Laminar Coil-less 34 is a shorter, more compact short path distillation arm which allows for higher temperatures in the vapor bypass. A true laminar with less turbulence. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar Coil-less 34
-
Fits Size 29 or 34 Fraction Finder Sensor (drop down menu) Details:
- Goes in-line between the condenser & collection flask, allowing you to use the Fraction Finder in a new location and still run a hot condenser.
- High temperatures can be problematic for our sensor; this relocates where Fraction Finder could be positioned.
- Watch this video to see how it works.
-
The Valved Laminar Path 29 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, (3) GL14s (1 cap) and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Laminar Path 29
-
The Valved Laminar Path 34 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, (3) GL14s (1 cap) and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Laminar Path 34
-
Liquid Temp Control Key 34/45 is a short path distillation head key that is used to generate a localized cold/hot surface. The temperature achieved reduces or enlarges the quantity of volatile material exhausted into the air. This premium Schott glass 34mm plug is 8.5 inch overall length and 4.5 inch from the bottom of the frosted taper with the tip being a small condenser coil. High Temp GL14s included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Liquid Temp Control Key 34/45
-
When the going gets tough, you can't ever be too safe! A triple coil intermediate trap with female 34/45 inlet and male outlet. This trapping mechanism is used as a laminar path connection recommended for larger short path distillation setups (22-50L) leading into dual cold traps. Heavy wall and joint thickness. Upgraded GL18 connections prevent barb breakage and mass body failure from stress of removing hoses. Extreme duty capacity and redesigned custom sized parallel flow coils that supply you with unmatched cooling. Collection flask port 45/50. Comes complete with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 3 Shorty
-
Liquid Temp Control Key 45/50 is a short path distillation head key that is used to generate a localized cold/hot surface. The temperature achieved reduces or enlarges the quantity of volatile material exhausted into the air. This premium Schott glass 45mm plug is 14.25 inch overall length and 10.5 inch from the bottom of the frosted taper with 4 large bands. High Temp GL14s included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Liquid Temp Control Key 45/50
-
The Short Path Distillation Head FC71 includes a 71/60 main bore with a 34/45 discharge and 34/45 thermoport. The 71 mm can handle bigger systems and a lot of product. A very versatile head that we can cater towards your needs. Comes with 34 key, 34 stopper well and GL14s. This limited edition short path distillation head (along with boiling flask) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with these boiling flasks: Summit has 5L and 12L options for this head. Please call us for more information. Clamp and stands not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC71
-
PLEASE CALL FOR AVAILABILITY. HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB2 150 comes equipped with 45/50 key port, 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB2 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB2 is designed to be ultra high speed with precision refinement. This head was bench marked by Heisenberg on a dual e2m30 array achieving 6 liters per hour without any effort at all. This head can be setup for very low temperatures, high clarity, and high speeds. Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. The HB2 150mm head comes included with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified.
-
HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB1 150 comes equipped with 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB1 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB1 is designed to be ultra selective to evacuate all previous fractions before the main body without letting the main body through. With some temp, main body can come out extremely fast and this head can be used as a first pass head. It is very effective in removing heads fractions while retaining main body components. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Please contact us for a completely tuned system with this hardware! Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. The HB1 150mm head comes with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified.
-
Boiling Flask 50L-3N-71 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) design. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. This limited edition boiling flask (along with short path distillation head) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. Joints are standard taper 24/40 (2) and 71/60 main. 50 Liter round bottom boiling flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with the Short Path Distillation Head FC71 head. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. RBF 50L-3N-71
-
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail: Parts: The Summit research spd-7/7.1 USPD systems are designed to fully refine products at a low temperature; preferred material required should be refined previously, or physically refined through all filtration and washing/chroma processes. Stands, crossbars and clamps sold separately. -
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail: Parts: The Summit research spd-7/7.1 USPD systems are designed to fully refine products at a low temperature; preferred material required should be refined previously, or physically refined through all filtration and washing/chroma processes. Stands, crossbars and clamps sold separately. -
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. 22 Liter assembly: Instagram Demo Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Head choice: SPD-6 Tall / SPD-6 Shorty / SPD-6 Nano
- Genesis Mantle
- Boiling Flask 22L-3N-55
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 liter (2)
- Receiving Flask 29 5 liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (4)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- High Temp GL14 (4)
- Appropriate key for your head choice
-
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Head choice: SPD-6 Tall / SPD-6 Shorty / SPD-6 Nano
- Genesis Mantle
- Boiling Flask 12L-3N-55
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 liter (2)
- Receiving Flask 29 5 liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (4)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- GL14 (4)
- Appropriate key for your head choice
-
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantle and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Choice of Head: SPD-6 FC45 Tall / SPD-6 FC45 Shorty / SPD-6 FC45 Nano
- Genesis Mantle
- Boiling Flask 12L-3N-45
- Laminar Path Monocow 29
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 liter (2)
- Receiving Flask 29 5 liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (4)
- Stopper 24 (2)
- Rare Earth PTFE Pill 28x70mm
- Rodaviss kit (2)
- GL14 (4)
- Appropriate key for head selection
-
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantle and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail. You will select your head at the bottom of this page.- Head choice: SPD-6 FC45 Tall / SPD-6 FC45 Shorty / SPD-6 FC45 Nano
- Genesis Mantle
- Boiling Flask 5L-3N-45
- Laminar Path Monocow 29
- Receiving Flask 29 1 Liter (2)
- Receiving Flask 29 2 liter (2)
- Receiving Flask 29 3 liter (2)
- Cold Trap 1 34 to GL
- Swage DV-2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34
- Stopper 24 (2)
- Rare Earth PTFE Pill 24x50mm
- Rodaviss kit
- GL14 (4)
- GL18 (2)
- GL18 Lock off cap
- Appropriate key head selection
-
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantle and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail:- Choice of Head: SPD-6 FC45 Tall / SPD-6 FC45 Shorty / SPD-6 FC45 Nano
- Genesis Mantle
- Boiling Flask 5L-3N-45
- Laminar Path Monocow 29
- Receiving Flask 29 1 Liter (2)
- Receiving Flask 29 2 liter (2)
- Receiving Flask 29 3 liter (2)
- Cold Trap 2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (3)
- Stopper 24 (2)
- Rare Earth PTFE Pill 24x50mm
- Rodaviss kit
- GL14 (4)
- Appropriate key for head selection
-
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail:- SPD Head Bertha 100
- Genesis Mantle
- Boiling Flask 22L-3N-100
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 Liter (2)
- Receiving Flask 29 5 Liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29
- Keck Clip 34 (5)
- Stopper 24 (2)
- Stopper Well 34
- Head Key Well 10 Band 34
- Head Key 21 Band 34
- Rare Earth PTFE Pill 28x70mm
- Rodaviss Kit (2)
- High Temp GL14 (4)
- PTFE O-Ring 100mm
- Flange Clamp 100mm
-
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail:- SPD Head Bertha 100
- Genesis Mantle
- Boiling Flask 12L-3N-100
- Laminar Path Monocow 34
- Receiving Flask 29 2 Liter (2)
- Receiving Flask 29 3 Liter (2)
- Receiving Flask 29 5 Liter (2)
- Cold Trap 2
- Cold Trap 2 Shorty
- Cold Trap Cap (2)
- Cold Trap Flask 1 Liter (2)
- Cold Trap 2 Hard Pipe
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29
- Keck Clip 34 (5)
- Stopper 24 (2)
- Stopper Well 34
- Head Key Well 10 Band 34
- Head Key 21 Band 34
- Rare Earth PTFE Pill 28x70mm
- Rodaviss Kit (2)
- High Temp GL14 (4)
- PTFE O-Ring 100mm
- Flange Clamp 100mm
-
22 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 22 liter kit, and a link for you to check them out in detail: Parts: This 22 Liter HB Package comes with two heads. The HB1 head has a built in key with heavy knock down and refinement with high speed. The HB2 head has a general theoretical plate at the bottom with a mean free pathway at top that includes a modified path distillation pathway. Combined with removable key, this head is your precision refiner. Stands, crossbars and clamps sold separately. -
12 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 12 liter kit, and a link for you to check them out in detail: Parts: This 12 Liter HB Package comes with two heads. The HB1 head has a built in key with heavy knock down and refinement with high speed. The HB2 head has a general theoretical plate at the bottom with a mean free pathway at top that includes a modified path distillation pathway. Combined with removable key, this head is your precision refiner. Stands, crossbars and clamps sold separately. -
5 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 5 liter kit, and a link for you to check them out in detail: Parts: This 5 Liter HB Package comes with two heads. The HB1 head has a built in key with heavy knock down and refinement with high speed. The HB2 head has a general theoretical plate at the bottom with a mean free pathway at top that includes a modified path distillation pathway. Combined with removable key, this head is your precision refiner. Stands, crossbars and clamps sold separately. -
2 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 2L kit, and a link for you to check them out in detail:- Short Path Distillation Head FC34
- Genesis Mantle
- Boiling Flask 2 Liter 24/24/34
- Laminar Path Monocow 29
- Receiving Flask 29 500ml (2)
- Receiving Flask 29 1 Liter (2)
- Cold Trap 1 34 to GL
- DV-2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34
- Stopper 24 (2)
- Well Stopper 24
- Short Key 24
- Rare Earth PTFE Pill 14x25mm
- Rodaviss Kit
- GL14 (4)
- GL18 (2)
- GL18 Lock Off Cap
-
2 Liter Short Path Distillation Package
Summit offers ready to assemble short path distillation kits that come with a top of the line calibrated Genesis Mantles and complete glassware setup. Everything pictured is included. If you would like to modify or add components (swap out for a larger receiving flask or add a KF25 plug), just call us, we can work with you on mostly anything. Here is a list of everything included in this 2L kit, and a link for you to check them out in detail:- Short Path Distillation Head FC34
- Genesis Mantle
- Boiling Flask 2 Liter 24/24/34
- Laminar Path Monocow 29
- Receiving Flask 29 500ml (2)
- Receiving Flask 29 1 Liter (2)
- Cold Trap 2
- Cold Trap Cap
- Cold Trap Flask 1 Liter
- Hard Pipe for Cold Trap
- KF25 Adapter 34
- Thermometer Adapter 24
- Keck Clip 29 (2)
- Keck Clip 34 (3)
- Stopper 24 (2)
- Well Stopper 24
- Short Key 24
- Rare Earth PTFE Pill 14x25mm
- Rodaviss Kit
- GL14 (4)
-
Premium Schott glass 24/40 plug. 5.5 inch overall length thermowell. 2 inch length from bottom of the frosted taper. Allows for accurate thermometer readings in the head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Well Stopper 24/40
-
Premium Schott glass 34/45 plug. 7.75 inch overall length thermowell. 3 inch length from bottom of the frosted taper. Allows for accurate thermometer readings in the head while allowing zero rejection compared to a key with bands. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Well Stopper 34/45
-
Premium Schott glass 45/50 well stopper. 4.75 inch length from bottom of the frosted taper. 9.5 inch overall length. Allows for accurate thermometer readings in the head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Well Stopper 45/50
-
The Fraction Finder Sensor #34 consists of an optical light pulse and detector, acting as “the eyes” of the system. It wraps around a distillation set up condenser tube and connects to the Fraction Finder display to track important data on the distillation. These sensors are black for a reason:
- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
The Fraction Finder Sensor #29 consists of an optical light pulse and detector, acting as “the eyes” of the system. It wraps around a distillation set up condenser tube and connects to the Fraction Finder display to track important data on the distillation. These sensors are black for a reason:
- Black absorbs all light while blocking out ambient light.
- This leads to better signaling and the most valid data possible transmitting to the Fraction Finder display.
- For example, a white sensor wouldn’t work because it would reflect the light into your glassware and into the sensor, harming the reading.
- This reduces any degradation from solvents, crude oils, extracts, etc..
- This protects the sensor and ensures that it lives to see an endless amount of runs.
- The black coating we use on each sensor is a high temperature, thermal resistant coating, it can withstand temperatures well above anything you’d see in a distillation lab.
- It’s nearly impossible to set one of our sensors on fire, the coating is almost completely fireproof!
- This protects the user, the equipment, and (in worst case scenarios) the entire lab.
-
Fits Size 29 Fraction Finder Sensor Details:
- Bundle that includes the Collection Jar Adapter and Collection Jar Mount
- For use with Wiped Film Evaporation systems, such as Root Sciences/VTA, to enable collected distillate to flow through the Size 29 Fraction Finder Sensor
- For use with Ball collection jar (not included)
-
$6,793.75
Atlas Copco GVD28 1 Phase, 110-120/200-230V, 50/60Hz. Pump oil and EMF20 with accessories are included.- Type of product: Vane Pump
- Condition: New
- Inlet: KF25
- Exhaust: Hose Nipple
- Motor: 1 Phase, 110-120/200-230V, 50/60Hz
- Oil: Hydrocarbon
- Pumping speed: 23.3 CFM (60 Hz)
- Ultimate vacuum: 7.7 x 10-4 Torr (without gas ballast)
- Weight: 97 lbs
-
100g Long term lubrication for high temperature applications under the influence of aggressive media up to 250C. Klübertemp GR RT greases are white, homogeneous long-term greases based on perfluorinated polyether oils (PFPE) and polytetrafluoroethylene (PTFE). This series contains greases with a range of specific additives for use in different applications. Klübertemp GR RT 15 shows good compatibility with plastics and elastomers, enabling a wide range of component materials to be selected. Vapor pressure of 2.0 x 10⁸ Torr at 20°C Vapor pressure of 4.7 x 10⁶ Torr at 100°C
-
This is a high precision inert gas regulation valve assembled at Micro Matic & calibrated at DigiVac.
- Forged brass and die cast for durability
- O-Ring inlet seal at tank connection
- Set screw pressure adjustment
- Flow control inlet
- Calibrated exclusively to the Summit sweep valve & vacuum controller
-
Receiving Flask 29/42 12 Liter round bottom flask designed with a 29mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. This massive 12L receiving flask has no warranty. Please use at your own risk. A skylift is recommended. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 29/42 12 Liter
-
Receiving Flask 29/42 5 Liter round bottom flask designed with a 29mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 29/42 5 Liter.
-
Receiving Flask 29/42 3 Liter round bottom flask designed with a 29mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 29/42 3 Liter.
-
Receiving Flask 29/42 2 Liter round bottom flask designed with a 29mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 29/42 2 Liter.
-
Receiving Flask 29/42 1 Liter round bottom flask designed with a 29mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 29/42 1 Liter.
-
Receiving Flask 29/42 500ml round bottom flask designed with a 29mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 29/42 500ml
-
Sale!Receiving Flask 24/40 1 Liter round bottom flask designed with a 24mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 24/40 1 Liter
-
Sale!Receiving Flask 24/40 250ml round bottom flask designed with a 24mm standard taper joint. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Receiving Flask 24/40 250ml