-
Hochstrom O-rings (2 included) that fits at the bottom of your Hochstrom filter™. Made from Viton, a synthetic rubber and fluoropolymer elastomer, that is chemical-resistant. 100% USA made.
-
KF16 O Ring will fit between any KF16 flange while using a KF16 clamp. Made from Viton and stainless steel.
-
$4,999.99
The new SPD-8 Series Heads (FC55, 60mm, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. This 2 liter head comes with boiling flask! Can be upgraded to 5 liter flask, please call us. Short Path Distillation 8 Head in use at the lab: Instagram Demo The condenser in this 60mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head:- Head Key Well 45/50
- Stopper Well 45/50
- High Temp GL18s (4)
- Flange Clamp 60mm
- PTFE O-Ring 60mm
- 2 Liter Boiling Flask
-
$5,224.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 150mm clamp with O-ring and PTFE GL18s (4) included. 45/50 Key port and appropriate key & well stopper. 34/45 discharge port. Our 150mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 150 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$4,849.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 150mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 150mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 150 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$4,499.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 100mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 100mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 100 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$15,300.00 *Price subject to change for different configurations
Kaeser Aircenters are the answer to many challenges. The integrated design reduces time spent planning and purchasing your air system. We combine the reliability, energy efficiency, and easy-to-service design of our industrial rotary screw compressors into a quiet, space-saving package complete with storage tank and air treatment equipment. Aircenters arrive completely assembled, saving you a lot of time and expense. Aircenters require little space and are the perfect solution for smaller industrial operations. With noise levels as quiet as 61 dB(A) you can install it anywhere without disrupting productivity.Included with your compressor:- Start-up Service
- CA Code Piping
- Clean Air Treatment Package (KE Filter + Eco-Drain on Tank)
- KCF 25 Condensate Filter with Mounting Kit
- 3/4" X 36" Flex Hose
-
$18,600.00 *Price subject to change for different configurations
Kaeser Aircenters are the answer to many challenges. The integrated design reduces time spent planning and purchasing your air system. We combine the reliability, energy efficiency, and easy-to-service design of our industrial rotary screw compressors into a quiet, space-saving package complete with storage tank and air treatment equipment. Aircenters arrive completely assembled, saving you a lot of time and expense. Aircenters require little space and are the perfect solution for smaller industrial operations. With noise levels as quiet as 61 dB(A) you can install it anywhere without disrupting productivity.Included with your compressor:- Start-up Service
- CA Code Piping
- Clean Air Treatment Package (KE Filter + Eco-Drain on Tank)
- KCF 25 Condensate Filter with Mounting Kit
- 3/4" X 36" Flex Hose
-
$21,100.00 *Price subject to change for different configurations
Kaeser Aircenters are the answer to many challenges. The integrated design reduces time spent planning and purchasing your air system. We combine the reliability, energy efficiency, and easy-to-service design of our industrial rotary screw compressors into a quiet, space-saving package complete with storage tank and air treatment equipment. Aircenters arrive completely assembled, saving you a lot of time and expense. Aircenters require little space and are the perfect solution for smaller industrial operations. With noise levels as quiet as 61 dB(A) you can install it anywhere without disrupting productivity.Included with your compressor:- Start-up Service
- CA Code Piping
- Clean Air Treatment Package (KE Filter + Eco-Drain on Tank)
- KCF 25 Condensate Filter with Mounting Kit
- 3/4" X 36" Flex Hose
-
$11,260.00
Presenting the Atlas Copco 10 HP air compressor. This is a single stage, air cooled, oil injected, rotary screw compressor with integrated dryer and 71 gallon tank (tank upgrades available, please contact us). 208-230/460 Volt AC 3-Phase 36.7 cfm. Also included:- compressor
- drive motor
- oil & air system
- electro-pneumatic controls
- coalescing filter
- oil water separator
- auto tank drain
- Powerful & reliable solution for small & medium sized industries
- 130 psi
- Manufactured & tested to meet ISO 9001/9002, ISO 14001 & ISO 1217
- Cools the compressed air & removes the water before it enters your network
- Prevents rust in compressed air piping & avoids damage to air tools
- Water separator with electronic no-loss water drain included
- Enclosure reduces sound levels so you work nearby
- Optimized cooling air flow enhances quiet operation
- Grouped together & accessible through the removable panel
- Spin-on oil separator & filter are easy to maintain
Weight: 692 PoundsProduct Length 60 InchesProduct Width 23 InchesProduct Height 52 Inches -
$2,800.00
The Sogevac single stage rotary vane pumps are required for any sized hardpiped system and can be very useful on hosed systems as well.- Inlet: KF40
- Motor: 1 Phase, 180/264V, 50/60Hz, 1.5kW, 12A
- Oil: synthetic hydrocarbon
- Pumping speed: 31 CFM (60Hz)
- Ultimate pressure: 0.5 mbar
- Compact design and small footprint
- Very low and constant noise level in any working condition
- Simplified maintenance
-
$3,400.00
Simple yet powerful, the GVS40A uses displacement and horsepower to achieve CFM. Unlike many other types of pumps that require complex fore traps, cryotraps, etc. – a well maintained single stage rotary vane can withstand great amounts abuse; making them very affordable and usable without much worry. Also know as 'roughing', 'wet' or 'backing' pumps. The GVS40A rotary vane pump is required for any sized hard-piped system and can be very useful on hosed systems as well.- Inlet: KF25
- Exhaust: 1 1/4" female threaded (ID)
- Motor: 1 Phase, 180/264V, 50/60Hz
- Oil: synthetic hydrocarbon
- Pumping speed: 31 CFM (60Hz)
- Ultimate pressure: 0.4 Torr
-
$4,299.99
The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo 34/45 key, 100mm clamp with O-ring and PTFE GL18s (4) included. 34/45 discharge port. Our 100mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 100 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$12,500.00
A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.Benefits
Important characteristics
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.-
All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
-
-
$13,500.00
A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.Benefits
Important characteristics
Performance Data Temperature Heating-up time to 100 °C [min] 80 Temperature fluctuation [± K] 0.1 Temperature range 15 °C above ambient temperature to [°C] 200 Temperature variation at 100 °C [± K] 2 Vacuum Data Leak rate [bar/h] 0.01 Permitted end vacuum [mbar] 0.01 Electrical data Nominal power [kW] 1.2 Phase (Nominal voltage) 1~ Power frequency [Hz] 50/60 Rated Voltage [V] 230 Unit fuse [A] 10 Connections Compressed air connection for pressure-encapsulation 8 mm Inert gas connection with flow limiter (RP") 3/8 Measuring access port with small flange [DN mm] 16 Vacuum connection with small flange [DN mm] 16 Housing dimensions not incl. fittings and connections Depth net [in] 21.67 Height net [in] 30.53 Width net [in] 25.02 Internal Dimensions Depth [in] 13.4 Height [in] 15.76 Width [in] 15.76 Measures Interior volume [cu.ft.] 1.9 Load per rack [lbs] 44 Net weight of the unit (empty) [lbs] 209 Permitted load [lbs] 99 Viewing window height [in] 12.1 Viewing window width [in] 13.79 Wall clearance back [in] 3.94 Wall clearance sidewise [in] 5.32 Fixtures Number of shelves (std./max.) 2/5 Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here: To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.-
All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
-
-
$17,500.00
A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.Benefits
Important characteristics
Performance Data Temperature Heating-up time to 100 °C [min] 95 Temperature fluctuation [± K] 0.1 Temperature range 15 °C above ambient temperature to [°C] 200 Temperature variation at 100 °C [± K] 3.5 Vacuum Data Leak rate [bar/h] 0.01 Permitted end vacuum [mbar] 0.01 Electrical data Nominal power [kW] 1.9 Phase (Nominal voltage) 1~ Power frequency [Hz] 50/60 Rated Voltage [V] 230 Unit fuse [A] 10 Connections Compressed air connection for pressure-encapsulation 8 mm Inert gas connection with flow limiter (RP") 3/8 Measuring access port with small flange [DN mm] 16 Vacuum connection with small flange [DN mm] 16 Housing dimensions not incl. fittings and connections Depth net [in] 26.4 Height net [in] 35.46 Width net [in] 29.16 Internal Dimensions Depth [in] 18.12 Height [in] 19.94 Width [in] 19.94 Measures Interior volume [cu.ft.] 4.1 Load per rack [lbs] 44 Net weight of the unit (empty) [lbs] 337 Permitted load [lbs] 143 Viewing window height [in] 16.27 Viewing window width [in] 17.97 Wall clearance back [in] 3.94 Wall clearance sidewise [in] 5.32 Fixtures Number of shelves (std./max.) 2/6 Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here: To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.-
All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
-
-
$14,285.00
Polyscience 3HP Heavy Duty Durachill will handle numerous tasks. Air cooled with simple operation and maintenance. When precision liquid cooling matters, go with Polyscience cooling solutions.- DuraChill® Chillers 2HP and up are not available outside of the United States
- High capacity cooling for plasma torch cutting, machine tool hydraulics, high powered lasers, and other high heat generating processes and equipment
- Displays temperature and pressure or flow rate simultaneously
- User-adjustable temperature, pressure, and flow rate alarms
- Simple operation and maintenance
- Wide variety of options available
-
$17,995.00
Polyscience 8HP Heavy Duty Air Cooled 3 Phase Chiller will handle different tasks - 50L roto rating. When precision liquid cooling matters, go with Polyscience cooling solutions.- DuraChill® Chillers 2HP and up are not available outside of the United States
- High capacity cooling for plasma torch cutting, machine tool hydraulics, high powered lasers, and other high heat generating processes and equipment
- Displays temperature and pressure or flow rate simultaneously
- User-adjustable temperature, pressure, and flow rate alarms
- Simple operation and maintenance
- Wide variety of options available
-
Size not available? New Genesis Mantles are in stock. Exciting features, intuitive touch screen technology and ground breaking up and down heating. Please contact Summit for more information or to get your mantle calibrated today! FREE ATHENA SOFTWARE (Techno Heat Mantle compatibility) Included with this digital touch screen mantle and high power heating system:
- Mantle
- Touch Screen Unit
- Controlled Heating Insulator Cap
- Dual Vapor Probes (with one backup each)
- Power Cable
-
$12,000.00 $9,990.00
Second to none in temperature uniformity, temperature stability and drying speed (purging). The combination of these high marks results in throughput (yield & productivity). This unit reaches 100°F in just 15 minutes thanks to the individual direct shelf heating. Each shelf has its own temperature controller for varying temperatures. KF25 full bore into the oven all the way to the chamber. No size reductions like in other ovens. These ovens are the real deal. CE & UL CERTIFIED! 9cu ft Vacuum oven specificationsElectric 110V 50/60Hz 1PH 13.6A, 1500W Chamber Size: 15.75 x 15 x 23" deep Material: Stainless Steel Capacity: 9 cubic feet Temperature control Controller: microcomputer with LCD display Range: ambient to 302°F Display units: Fahrenheit or Celsius Accuracy: +/- 0.1°F Uniformity: +/- 0.5 at 100°F5 Controllers (individual direct shelf heating)Warm-up time to 100°F: 15 minutes (without load) Vacuum Range: 0 to 76 cmHg (0 to 0.1MPa) Vacuum port: KF25 flange x1, KF25 strait pipe with elbow x1, KF25 clamps and o-rings x2 (ALL INCLUDED)Vent port: 3/8" female threaded Weight Unit: 555 Lbs, shipping: 747 Lbs Dimensions (WxDxH) Unit: 38 x 37 x 32" Shipping: 45 x 45 x 44" Shelves 5 fixed and individually heated shelves, 23x27" each Distance between shelves: 4"Area: 23x27" , 345 sq inches Door gasket material Food grade silicone Observation window 3/4" tempered glass Safety Built in circuit breaker, over-temp protector In-door lights LED CE & UL compliance Yes -
$5,000.00 $4,290.00
- 7 Du-aluminium Shelves (Superb heat conductivity) - Excellent temperature uniformity and accuracy - Stainless Steel Internal Chamber with shelves - Safety assurance with C.E and U.L. conformity KF25 full bore into the oven all the way to the chamber. No size reductions like in other ovens. These ovens are the real deal. CE & UL CERTIFIED! 3.4 cu ft Vacuum oven specificationsElectric 110V 50/60Hz 1PH 12.3A, 1350W Chamber Size: 15.75 x 15 x 23" deep Material: Stainless Steel Capacity: 3.4 cubic feet Temperature control Controller: microcomputer with LCD display Range: ambient to 302°F Display units: Fahrenheit or Celsius Accuracy: +/- 0.1°F Uniformity: +/- 0.5 at 100°F1 ControllerWarm-up time to 100°F: 40 minutes (without load) Vacuum Range: 0 to 76 cmHg (0 to 0.1MPa) Vacuum port: KF25 flange x1, KF25 strait pipe with elbow x1, KF25 clamps and o-rings x2 (ALL INCLUDED) Vent port: 3/8" female threaded Weight Unit: 255 Lbs, shipping: 423 Lbs Dimensions (WxDxH) Unit: 35 x 32 x 28" Shipping: 42 x 39 x 39" Shelves 10 removable shelves, 15 x 23" (WxD) each Distance between shelves: 1.5"Area: 15x23" , 345 sq inches Door gasket material Food grade silicone Observation window 3/5" tempered glass Safety Built-in circuit breaker, over-temp protector In-door lights LED CE & UL compliance Yes -
$6,000.00
Size not available? New Genesis Mantles are in stock. Exciting features, intuitive touch screen technology and ground breaking up and down heating. Please contact Summit for more information or to get your mantle calibrated today! FREE ATHENA SOFTWARE (Techno Heat Mantle compatibility) Included with this digital touch screen mantle and high power heating system:- Mantle
- Touch Screen Unit
- Controlled Heating Insulator Cap
- Dual Vapor Probes (with one backup each)
- Power Cable
-
Out of stockSize not available? New Genesis Mantles are in stock. Exciting features, intuitive touch screen technology and ground breaking up and down heating. Please contact Summit for more information or to get your mantle calibrated today! FREE ATHENA SOFTWARE (Techno Heat Mantle compatibility) Included with this digital touch screen mantle and high power heating system:
- Mantle
- Touch Screen Unit
- Controlled Heating Insulator Cap
- Dual Vapor Probes (with one backup each)
- Power Cable
-
Out of stockSize not available? New Genesis Mantles are in stock. Exciting features, intuitive touch screen technology and ground breaking up and down heating. Please contact Summit for more information or to get your mantle calibrated today! FREE ATHENA SOFTWARE (Techno Heat Mantle compatibility) Included with this digital touch screen mantle and high power heating system:
- Mantle
- Touch Screen Unit
- Controlled Heating Insulator Cap
- Dual Vapor Probes (with one backup each)
- Power Cable
-
$3,000.00
Size not available? New Genesis Mantles are in stock. Exciting features, intuitive touch screen technology and ground breaking up and down heating. Please contact Summit for more information or to get your mantle calibrated today! FREE ATHENA SOFTWARE (Techno Heat Mantle compatibility) Included with this digital touch screen mantle and high power heating system:- Mantle
- Touch Screen Unit
- Controlled Heating Insulator Cap
- Dual Vapor Probes (with one backup each)
- Power Cable
-
$10,585.00
Presenting the Atlas Copco 7.5 HP air compressor. This is a single stage, air cooled, oil injected, rotary screw compressor with integrated dryer and 53 gallon tank (tank upgrades available, please contact us). 21.2 cfm. Also included:- compressor
- drive motor
- oil & air system
- electro-pneumatic controls
- coalescing filter
- oil water separator
- auto tank drain
- Powerful & reliable solution for small & medium sized industries
- Manufactured & tested to meet ISO 9001, ISO 14001 & ISO 1217
- Cools the compressed air & removes the water before it enters your network
- Prevents rust in compressed air piping & avoids damage to air tools
- Water separator with electronic no-loss water drain included
- Enclosure reduces sound levels so you work nearby
- Optimized cooling air flow enhances quiet operation
- Grouped together & accessible through the removable panel
- Spin-on oil separator & filter are easy to maintain
-
$9,669.00
Presenting the Atlas Copco 5 HP air compressor. This is a single stage, air cooled, oil injected, rotary screw compressor with integrated dryer and 53 gallon tank. 16.6 cfm. Also included:- compressor
- drive motor
- oil & air system
- electro-pneumatic controls
- coalescing filter
- oil water separator
- auto tank drain
- Powerful & reliable solution for small & medium sized industries
- Manufactured & tested to meet ISO 9001, ISO 14001 & ISO 1217
- Cools the compressed air & removes the water before it enters your network
- Prevents rust in compressed air piping & avoids damage to air tools
- Water separator with electronic no-loss water drain included
- Enclosure reduces sound levels so you work nearby
- Optimized cooling air flow enhances quiet operation
- Grouped together & accessible through the removable panel
- Spin-on oil separator & filter are easy to maintain
-
$3,000.00
Polyscience AD 7 Liter Heater. Laboratory liquid heating at your fingertips.Description Temperature range of 10°C to 200°C , 7 Liter Heating Circulator Controller Type Advanced DigitalDisplay 3.75" Touch-Pad LCDConnectivity Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe- Intuitive 3.75” (9.5 cm) display with touch pad control
- Swivel 180™ rotating controller
- On-board connectivity: USB-A & B, Ethernet, RS-232/RS-485, and external temperature probe
- On-screen prompts
- Automatic performance optimization and specific heat tuning
- Single-point calibration capability
-
$248.00
I 19 Standard Vacuum Pump Fluid. 5 Gallons (18.927 Liters) Hydrocarbon fluid for mechanical vacuum pumps used in non-corrosive applications. This premium grade oil produces lower vapor pressures, reduced backstreaming, and has longer fluid life. sds To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.