-
1" Male JIC to KF25 adapter (Harvest Right Adapter) fits any KF25 flange. Summit's stainless adapters contain 100% USA made precision billet steel. Why choose an adapter with multiple parts and more chances to leak? -
The KF16 to Male 24/40 PTFE Adapter is typically used to convert a glass system to a vacuum system or sensor. Adapter has 11mm bore. Secure your male connection with a keck clip. PTFE billet parts made right here in the USA. Be sure to have KF16x10 Centering Ring and KF16 clamp to make your KF16 connection. -
The KF40 Bellow is a corrugated stainless steel pipe that connects to corresponding kf40 flanges. These malleable pipes allow for some error as apposed to hooking up a solid straight pipe. Available in 24 and 36 inch lengths. Don't forget other KF40 fittings and accessories: 100% stainless steel. 100% USA made. Bellow warning: Stretch and bend your bellow into position before installation. Engaging your pump(s) while not doing so could make the bellow jolt/jostle, putting stress on or damage glassware, voiding limited warranties. KF40 Bellow -
Looking to take your short path system to the next level? A diffusion pump will provide deeper vacuum and lower temps resulting in higher efficiency and increased speed. Package comes with an Edwards 30 roughing pump, the adapters to connect the diffusion, chiller to control temperatures and custom built and tuned SVG-3 setup with UHVP Sensor.- High rate Diffusion Pump
- Adapters to fit
- 3/4 HP Chiller
- E2M30 kit
- SVG-3 (3 zone gauge)
- UHVP Sensor
-
$16,710.00
Rebuilt Edwards E2M80 + Blower (mechanical booster) All air cooled dual stage Rotary Vane Pump, 208 V, 50 Hz/208-230 V, 60 Hz/460 V, 60 Hz, Three Phase with KF-40 inlet to blower. Edwards E2M series two stage oil sealed rotary vane vacuum pumps are renowned for their high ultimate vacuum, rapid pumping speeds, quiet operation and ability to handle water vapor. These direct drive rotary vane pumps are inherently compact and vibration free. Blowers add a dimension of vacuum that tops most dual pump options. Mechanical boosters feature the unique hydro-kinetic drive that provides pump down times cut by 50%, when compared with direct drive pumps, no bypass lines or pressure switches required, universal voltage motors, reduced capital and operating costs, air cooled motors – with water cooled options, and quiet, minimum vibration. Operating at relatively low pressures, the mechanical booster pump is not exposed to the same concentrations of corrosive process media as is the backing pump, which makes it highly reliable. Comes with Pump, Blower, MF100 filter and I 19 Standard fluid. To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$3,400.00
Simple yet powerful, the GVS40A uses displacement and horsepower to achieve CFM. Unlike many other types of pumps that require complex fore traps, cryotraps, etc. – a well maintained single stage rotary vane can withstand great amounts abuse; making them very affordable and usable without much worry. Also know as 'roughing', 'wet' or 'backing' pumps. The GVS40A rotary vane pump is required for any sized hard-piped system and can be very useful on hosed systems as well.- Inlet: KF25
- Exhaust: 1 1/4" female threaded (ID)
- Motor: 1 Phase, 180/264V, 50/60Hz
- Oil: synthetic hydrocarbon
- Pumping speed: 31 CFM (60Hz)
- Ultimate pressure: 0.4 Torr
-
$2,800.00
The Sogevac single stage rotary vane pumps are required for any sized hardpiped system and can be very useful on hosed systems as well.- Inlet: KF40
- Motor: 1 Phase, 180/264V, 50/60Hz, 1.5kW, 12A
- Oil: synthetic hydrocarbon
- Pumping speed: 31 CFM (60Hz)
- Ultimate pressure: 0.5 mbar
- Compact design and small footprint
- Very low and constant noise level in any working condition
- Simplified maintenance
-
$10,600.00
The dry screw pump VACUU·PURE® 10C reliably delivers the benefits of oil-free vacuum technology in the pressure range of 10-3 mbar. The new vacuum pump combines three important benefits for the user: 100% oil-free, chemically resistant, and no wear parts. VACUU·PURE 10C is ideally suited for clean processes and the production of pure products. The screw pump is especially designed for processes in the vacuum range down to 10-3 mbar, however unlike other fine vacuum technologies it can be used across the entire pressure range from atmospheric pressure to its ultimate vacuum. At the same time, aggressive gases and vapors can be pumped without any worries because of the high chemical resistance. The use of a cold trap is no longer necessary in the majority of applications. VACUU·PURE easily handles high vapor loads through its extraordinary condensate compatibility. Thanks to this capability, a gas ballast is unnecessary, avoiding associated disadvantages like the reduction in pumping speed and an increase in noise levels. The integrated regeneration mode enables rapid drying of the pump at the end of the process. This allows sample throughput to be increased significantly as compared to other pump technologies.Specification VACUU·PURE 10C Max. pumping speed 9 m3/h Ultimate vacuum (abs.) 5 x 10-3 mbar (at 1013 mbar ambient pressure) Max. inlet pressure (abs.) atmospheric pressure Max. outlet pressure (abs.) 15 mbar above atmospheric pressure Ambient temperature range (operation) 10 - 40 °C Ambient temperature range (storage) -10 - 60 °C Inlet connection KF 25 flange Outlet connection KF 25 flange Rated motor power 0.7 kW Protection class IP 20 Dimensions (L x W x H), approx. 507 x 269 x 413 mm Weight, approx. 21.5 kg Noise (sound pressure level), uncertainty 3 dBA 55 dBA Items supplied Pump completely mounted, ready for use, connection with small flange KF DN 25 (2x centering and clamping rings included), with manual. To establish a hose nozzle connection, suitable KF flanges with hose nozzle are available for order. 
For more details or manual, visit VacuuBrand directly.
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
Mechanical valve for the use with Apollo Vacuum Controller or SVG-3 This KF25 elbow valve works by throttling the pressure between the vacuum pump and the process to control the vacuum level or to isolate the vacuum pump | Enables vacuum pressure control using a solenoid valve for throttling pump suction- Control range: 10 millitorr to 6 Torr
- Measurement range: 1 millitorr to 760 Torr
- Range with accuracy: 10 millitorr to 6 Torr
- Benefits of throttle control: With the KF25 1″ orifice you get better and faster throughput | ideal for processing high volumes | Extends life of pump by enabling pump to run closer to it’s base pressure
- Vacuum control—Regulate the vacuum level between the vacuum pump and the chamber or process. It creates a pressure drop between the two, thereby allowing the process to operate at a set pressure while the pumps’ pressure varies based on loading. Helps prolong the life of your vacuum pump!
- Vacuum controller applications: Vacuum Ovens, Vacuum Furnaces, Vacuum Bagging or Composites
- Botanical processing: Rotary Evaporation, Short Path Distillation (1 Head Kit), Extractions
- Use case example— To maintain specific pressure levels in a vacuum oven at about 2 Torr to avoid removing target terpenes and only removing water
-
$6,500.00
Diffusion pump 06A with high volume operation at UHVP rates. This 06A is the larger of the two diff pumps we sell, satisfies requirements for 12 liter short path setups and over. Liquid cooled pump well-suited for use in chemical manufacturing, where large quantities of gas have to be pumped away as quickly as possible. With no moving parts, these pumps are rugged and extremely reliable. Stainless steel is used for the pump bodies in order to minimize outgassing of the pumps, eliminate corrosion and to ensure a long operating lifetime of the pump. In short, diffusion pumps provide deeper vacuum and lower temps resulting in higher efficiency and increased speed. Comes with $900 dollars in flanges, connectors and diff oil. Comes stock with KF40 flanges but can always be sized (KF25, KF16, ECT). To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$5,791.48
Diffusion pump 04A with high volume operation at UHVP rates. This 04A is the smaller of the two diff pumps we sell, satisfies requirements for 12 liter short path setups and under. Liquid cooled pump well-suited for use in chemical manufacturing, where large quantities of gas have to be pumped away as quickly as possible. With no moving parts, these pumps are rugged and extremely reliable. Stainless steel is used for the pump bodies in order to minimize outgassing of the pumps, eliminate corrosion and to ensure a long operating lifetime of the pump. In short, diffusion pumps provide deeper vacuum and lower temps resulting in higher efficiency and increased speed. Comes with $900 dollars in flanges, connectors and diff oil. Comes stock with KF25 flanges but can always be sized (KF40, KF16, ECT). To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
$9,630.49
Rebuilt Edwards E2M40 + Blower (mechanical booster) All air cooled dual stage Rotary Vane Pump, 208 V, 50 Hz/208-230 V, 60 Hz/460 V, 60 Hz, Three Phase with KF-40 inlet to blower. Edwards E2M series two stage oil sealed rotary vane vacuum pumps are renowned for their high ultimate vacuum, rapid pumping speeds, quiet operation and ability to handle water vapor. These direct drive rotary vane pumps are inherently compact and vibration free. Blowers add a dimension of vacuum that tops most dual pump options. Mechanical boosters feature the unique hydro-kinetic drive that provides pump down times cut by 50%, when compared with direct drive pumps, no bypass lines or pressure switches required, universal voltage motors, reduced capital and operating costs, air cooled motors – with water cooled options, and quiet, minimum vibration. Operating at relatively low pressures, the mechanical booster pump is not exposed to the same concentrations of corrosive process media as is the backing pump, which makes it highly reliable. Comes with Pump, Blower, MF100 filter and I 19 Standard fluid. To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
Adapter fits any KF25 flange with KF25 o-ring and KF25 clamp. Threads are 0.25 inch BSPP. Commonly used for wipers (wiped film or rolling film) using Summit Discharge Pumps. Single adapter only. 100% Billet stainless steel and 100% USA made. -
The Discharge Pump allows you to remove fluid from your system without breaking vacuum. This would replace the need for receiving flasks. Controller box allows you to regulate heat and speed at the touch of a finger. You will need to elevate/modify your current short path system to utilize this pump. Instagram Demo
Included:
- Discharge Pump
- Pump Controller
-
The Apollo Proportional Vacuum Controller is an advanced scientific laboratory vacuum controller, display, digital readout, and vacuum live reading analysis device. This version of the Apollo can service up to FOUR REMOTE vacuum sensors of any kind with up to FOUR REMOTE vacuum valves that are controlled by the Digi-Vac dinamo proportional live CFM control valve. KF25 flanges, barbed breather valve. This device is essential for high speed rotary evaporation control and crucial for controlling and even increasing recovery rates on falling film evaporation machines. Those might be the top two, but the possibilities are rising with new tech that have KF25 fitment. The device has a continuous CFM open-close valve that never actually stops moving. Typically it will not close but the effect is reached with the ability to increase or decrease CFM size allowing to maintain vacuum select point control. If the set point comes up, it will close the valve. If the set point goes down it will open the valve. Typically very minute movements inside make a huge performance difference and increase in vacuum pump performance allowing continual cfm-to-micron control. This Apollo controller can be expanded but comes with ONE EXTERNAL COUPLED device standard. This is an Apollo brain unit with a chemical duty touch screen, with remote valve/sensor. Standard options are as follows:- The first board location is equipped by summit with one sensor designed for aggressive solvent use and one proportional valve (dinamo valve).
- Three more slots are available to accept up to three more sensors and three more valves.
- The additional optional upgrade is only several hundred dollars for each additional proportional valve control added-on. any length cable can be used, please inform us for a specialty need with longer cables than what is supplied.
-
$14,095.00
Specifications- Type of Product: Scroll Pump
- Manufacturer: Edwards
- Condition: New
- Part Number: A73001983
- Inlet: KF40
- Exhaust: KF25
- Motor: 1 Phase, 100-120/200-230V, 50/60Hz
- Pumping speed: 21 CFM
- Ultimate vacuum: 8 x 10-3 Torr
- Weight: 105 lbs
- closed loop temperature monitoring
- dry, clean vacuum free of lubricants
- simple, single-sided scroll design
- patented isolated bearing shield
- world-wide voltage compatibility
- low power consumption
- controllable gas ballast
- inverter driven motor
-
$7,117.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF25
- Exhaust: KF16
- Motor: 1 Phase, 100-115/220-230V, 50/60Hz
- Pumping speed: 7.53 CFM (50Hz), 9.06 CFM (60Hz)
- Ultimate pressure: 1 x 10-2 Torr
- Weight: 75 lbs
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$5,490.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF25
- Exhaust: KF16
- Motor: 1 Phase, 100-120/200-240V, 50/60Hz
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$5,164.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF25
- Exhaust: KF16
- Motor: 1 Phase, 100-120/200-240V, 50/60Hz
- Pumping speed: 4.23 CFM (50Hz), 5.35 CFM (60Hz)
- Ultimate pressure: 3 x 10-2 Torr (50Hz), 2 x 10-2 Torr (60Hz)
- Weight: 54 lbs
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$2,977.00
Specifications- Manufacturer: Agilent
- Condition: New
- Part Number: IDP3B01
- Inlet: KF16
- Exhaust: 1/4" FNPT
- Motor: 1 Phase, 115V, 60Hz
- Pumping speed: 1.76 CFM (50Hz), 2.11 CFM (60Hz)
- Ultimate pressure: 2.5 x 10-1 Torr
- Weight: 21 lbs
- Low noise and vibration.
- Oil-free and contamination-free.
- High pumping speed provides rapid pump down and high gas throughput.
- Very low base pressure ensures optimal turbo pump performance with increased system reliability.
- IDP Pumps fully isolate the bearings and motor from the vacuum space and contain all pumped gases.
- Scroll pump technology’s long service interval results in low cost of ownership.
- Easy to integrate: minimal burden on system utilities& suitable for use inside cabinet enclosures.
- At only 21 pounds (9.5 kg), IDP Pumps are lighter than mechanical rotary vane and membrane pumps of similar pumping speed.
-
$6,793.75
Atlas Copco GVD28 1 Phase, 110-120/200-230V, 50/60Hz. Pump oil and EMF20 with accessories are included.- Type of product: Vane Pump
- Condition: New
- Inlet: KF25
- Exhaust: Hose Nipple
- Motor: 1 Phase, 110-120/200-230V, 50/60Hz
- Oil: Hydrocarbon
- Pumping speed: 23.3 CFM (60 Hz)
- Ultimate vacuum: 7.7 x 10-4 Torr (without gas ballast)
- Weight: 97 lbs
-
$7,275.00
Edwards E2M28, 1 Phase, 115-240V, 50/60Hz vacuum pump. Pump oil and EMF20 with accessories are included.- Type of product: Vane Pump
- Condition: New
- Inlet: KF25
- Exhaust: KF25
- Motor: 1 Phase, 115-240V, 50/60Hz
- Oil: Hydrocarbon
- Pumping speed: 19.5 CFM (60Hz)
- Ultimate pressure: 7.5 x 10-4 Torr (without gas ballast)
- Weight: 97 lbs
-
$6,831.25
Edwards E2M28, 1 Phase, 115-240V, 50/60Hz vacuum pump. Pump oil and EMF20 with accessories not included.- Type of product: Vane Pump
- Condition: New
- Inlet: KF25
- Exhaust: KF25
- Motor: 1 Phase, 115-240V, 50/60Hz
- Oil: Hydrocarbon
- Pumping speed: 19.5 CFM (60Hz)
- Ultimate pressure: 7.5 x 10-4 Torr (without gas ballast)
- Weight: 97 lbs
-
$4,685.00
Atlas Copco GVD28 1 Phase, 110-120/200-230V, 50/60Hz. Pump oil and EMF20 with accessories not included.- Type of product: Vane Pump
- Condition: New
- Inlet: KF25
- Exhaust: Hose Nipple
- Motor: 1 Phase, 110-120/200-230V, 50/60Hz
- Oil: Hydrocarbon
- Pumping speed: 23.3 CFM (60 Hz)
- Ultimate vacuum: 7.7 x 10-4 Torr (without gas ballast)
- Weight: 97 lbs
-
100g Long term lubrication for high temperature applications under the influence of aggressive media up to 250C. Klübertemp GR RT greases are white, homogeneous long-term greases based on perfluorinated polyether oils (PFPE) and polytetrafluoroethylene (PTFE). This series contains greases with a range of specific additives for use in different applications. Klübertemp GR RT 15 shows good compatibility with plastics and elastomers, enabling a wide range of component materials to be selected. Vapor pressure of 2.0 x 10⁸ Torr at 20°C Vapor pressure of 4.7 x 10⁶ Torr at 100°C -
This is a high precision inert gas regulation valve assembled at Micro Matic & calibrated at DigiVac.- Forged brass and die cast for durability
- O-Ring inlet seal at tank connection
- Set screw pressure adjustment
- Flow control inlet
- Calibrated exclusively to the Summit sweep valve & vacuum controller
-
Micro-controllable inert gas valve that installs directly to your boiling flask. Sweep valve connects to your calibrated sweep gas regulator. These components give you even more control with the Apollo Vacuum Controller. Complete control at your fingertips! Included:- KF16 (PTFE non-expanding material) to 24/40 fitting
- KF16 O-ring
- KF16 Clamp
- Extended tube sensor with threading
- Wiring
-
KF25 stainless steel 90 degree elbow for high vacuum applications. Don't forget your clamps! Summit has other KF25 products in our Stainless Steel section. -
Sale!
The Vacuubrand 4C Vario Diaphragm Pump is an excellent solution for labs working with most high boiling point solvents. This pump's three stage configuration gives it an ultimate vacuum rating of 1.5 mbar. The integrated vacuum controller (CVC-3000 included) provides an easy-to-use, application based interface that covers all common lab applications. The vacuum controller has you covered. Use manual set-point-control for simple processes, run fully automated distillations, or create your own application with simple drag-and-drop editing. For solvent evaporation, the vacuum controller continuously detects the boiling point and automatically adjusts the vacuum process as necessary. VARIO's on-demand motor speed control results in whisper-quiet operation and unparalleled length of service intervals for wear parts. Also available 12C Vario -
$16,500.00
These Vacuubrand VARIO® pumping units feature a very high pumping speed even close to the outstanding ultimate vacuum and are ideal for high vacuum requirements with most high boiling solvents. They provide precise vacuum control by continuously adjusting the pump´s motor speed. The controller provides fully automatic evaporations without any need for parameter input. The pump design offers exceptionally high chemical resistance supporting almost universal usage in chemistry and pharmaceutics. The NT VARIO pumping unit relies on a well-proven operating concept for evaporations with large amounts of solvents. The inlet separator (AK) retains particles and liquid droplets, the waste vapor condenser at the outlet (EK) is highly efficient and compact. The condenser enables near-100-percent solvent recovery, efficient recycling, and active protection of the environment. The NT VARIO can be equipped with these accessories later. The Vario 12c pump is an excellent solution for those who need high pumping speed and are working with high boiling point solvents. Combined with the reliability born of its chemical resistant fluoropolymer and perfluoroelastomer wetted materials, this pump delivers reliable performance for floor-standing rotary evaporators, vacuum drying ovens, vacuum distillation columns, and other similar applications. The integrated vacuum controller provides an easy-to-use, application based interface that covers all common lab applications. The vacuum controller has you covered. Use manual set-point-control for simple processes, run fully automated distillations, or create your own application with simple drag-and-drop editing. For solvent evaporation, the vacuum controller continuously detects the boiling point and automatically adjusts the vacuum process to maintain process control. With VARIO control, the pump runs only as fast is necessary. This extends the maintenance intervals and makes the pumping unit whisper quiet. Also available 4c VarioPerformance features
- Automatic adjustment of the vacuum level throughout the process for high process reproducibility and unattended operation
- Short process times due to zero-fluctuation (hysteresis-free) vacuum control, even for large amounts of vapor
- Removable CVC 3000 vacuum controller, can be arranged flexibly, easily operated with clear text menus
- Extraordinary diaphragm life for minimum operational and servicing costs
- PC 3012 NT VARIO: excellent environmental friendliness due to efficient solvent recovery, inlet separator for demanding applications
