spd

  • Apollo Proportional

    Apollo Proportional Vacuum Controller

    $3,999.99
    The Apollo Proportional Vacuum Controller is an advanced scientific laboratory vacuum controller, display, digital readout, and vacuum live reading analysis device. This version of the Apollo can service up to FOUR REMOTE vacuum sensors of any kind with up to FOUR REMOTE vacuum valves that are controlled by the Digi-Vac dinamo proportional live CFM control valve. KF25 flanges, barbed breather valve. This device is essential for high speed rotary evaporation control and crucial for controlling and even increasing recovery rates on falling film evaporation machines. Those might be the top two, but the possibilities are rising with new tech that have KF25 fitment. The device has a continuous CFM open-close valve that never actually stops moving. Typically it will not close but the effect is reached with the ability to increase or decrease CFM size allowing to maintain vacuum select point control. If the set point comes up, it will close the valve. If the set point goes down it will open the valve. Typically very minute movements inside make a huge performance difference and increase in vacuum pump performance allowing continual cfm-to-micron control. This Apollo controller can be expanded but comes with ONE EXTERNAL COUPLED device standard. This is an Apollo brain unit with a chemical duty touch screen, with remote valve/sensor. Standard options are as follows:
    • The first board location is equipped by summit with one sensor designed for aggressive solvent use and one proportional valve (dinamo valve).
    Further up-gradable options are as follows:
    • Three more slots are available to accept up to three more sensors and three more valves.
    • The additional optional upgrade is only several hundred dollars for each additional proportional valve control added-on.  any length cable can be used, please inform us for a specialty need with longer cables than what is supplied.
    This unit is not the same as Apollo Vacuum Controller  
    Add to cart Details
  • Sweep Valve

    Apollo Sweep Valve Kit

    $999.99
    Micro-controllable inert gas valve that installs directly to your boiling flask. Sweep valve connects to your calibrated sweep gas regulator. These components give you even more control with the Apollo Vacuum Controller. Complete control at your fingertips! Included:
    • KF16 (PTFE non-expanding material) to 24/40 fitting
    • KF16 O-ring
    • KF16 Clamp
    • Extended tube sensor with threading
    • Wiring
    Add to cart Details
  • Apollo Vacuum Controller

    Apollo Vacuum Controller

    $3,499.99
    The Apollo Vacuum Controller is an advanced scientific laboratory vacuum controller, display, digital readout, and vacuum live reading analysis device. (Pictured here shows location of the display and first 536 sensor {above}. Second picture shows location of second 536 sensor off the vacuum pump line {below}) This controller not only shows real time data for your laboratory process, it can also be used as a live pump down curve testing device for vacuum pumps in your lab. From seeing guaranteed accurate readings in your short path system to identifying the health of your pump, the Apollo is the most advanced tool in your arsenal when it comes to vacuum control with accuracy and quality second to none. All Summit hardware is now compatible with the new free ATHENA software. Here is a Youtube to help install. Do you have a rotary evaporator or falling film that needs full vacuum control? Take a look at the Proportional Vacuum Controller.   Standard options:
    • The first two pre-installed board locations have two 536 cleanable sensors (KF25), factory calibrated to a NIST certified test bench on each device prior to shipping. Usually one sensor is attached to the laminar portion of a short path to tell you what is going on in the system, and the second is attached to the pump to tell you the health and performance of the pump array in use.
    • A third board location is pre-installed and pre-calibrated for the use of a UHVP sensor (ultra high vacuum pressure) which is an option to be added-on if the user wants to use a third pump bay accessory like a diffusion pump or turbo pump etc. without any further needed upgrades to the Apollo itself.
    • A fourth board location is pre-installed for phantom power. There are two phantom power ports used to control the optional added-on feature on external control valves.  Each are independently controlled by the Apollo core software built in. With no needed upgrades to the Apollo itself.
    • A fifth board location is pre-installed with sweep valve controlling hardware.
    This device comes with the control box (brain), the digital chemical duty touch screen, two 536 sensors and all necessary device cables and cords. (everything in last picture) Spec Sheet Button Upgrades are:
    • Inert gas sweep valve kit and pressure regulator for turbo charging system speeds in various processes.
    • Up to two phantom powered Edwards bellow valves for vacuum valve control of wet or dry vacuum operation.
    • UHVP Sensor for additional diffusion or turbo control.
    Custom configurations allow the Apollo to be configured directly from summit with up to four sensors, and four control valves, both proportional and on/off style. Please inquire if you want your Apollo Vacuum Controller you've purchased expanded and/or modified.
    Add to cart Details
  • Binder Vacuum Oven 0.8

    Binder Vacuum Oven 0.8

    $12,500.00

    A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.

    Benefits

    • Fast and gentle drying
    • Direct heat transfer through large thermal conducting plates
    • Safe work with one-of-a-kind safety concept
    • Coordinated, modular system with vacuum pump and vacuum module
    • 2 year warranty

    Important characteristics

      • Temperature range: room temperature plus 15 °C to 200 °C
      • ATEX compliance chamber's interior: Ex II 3/-G Ex h IIB T1-T3 Gc X
      • APT.line™ preheating chamber technology
      • Controller with time-segment and real-time programming
      • 2 aluminum expansion racks
      • Inert gas connection
      • Shatterproof, spring-mounted safety glass panel
      • Pressurized instrument panel with compressed air connection
      • Pressure control device for heating activated < 125 mbar
      • Flame protection gasket
      • Class 2 independent adjustable temperature safety device (DIN 12880) with visual alarm
      • Computer interface: RS 422
    Performance Data Temperature
    Heating-up time to 100 °C [min] 65
    Temperature fluctuation [± K] 0.1
    Temperature range 15 °C above ambient temperature to [°C] 200
    Temperature variation at 100 °C [± K] 1.5
    Vacuum Data
    Leak rate [bar/h] 0.01
    Permitted end vacuum [mbar] 0.01
    Electrical data
    Nominal power [kW] 0.8
    Phase (Nominal voltage) 1~
    Power frequency [Hz] 50/60
    Rated Voltage [V] 230
    Unit fuse [A] 10
    Connections
    Compressed air connection for pressure-encapsulation 8 mm
    Inert gas connection with flow limiter (RP") 3/8
    Measuring access port with small flange [DN mm] 16
    Vacuum connection with small flange [DN mm] 16
    Housing dimensions not incl. fittings and connections
    Depth net [in] 19.7
    Height net [in] 25.81
    Width net [in] 20.29
    Internal Dimensions
    Depth [in] 11.62
    Height [in] 11.23
    Width [in] 11.23
    Measures
    Interior volume [cu.ft.] 0.8
    Load per rack [lbs] 44
    Net weight of the unit (empty) [lbs] 139
    Permitted load [lbs] 77
    Viewing window height [in] 8.16
    Viewing window width [in] 9.85
    Wall clearance back [in] 3.94
    Wall clearance sidewise [in] 5.32
    Fixtures
    Number of shelves (std./max.) 2/4
    1. All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
    Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here: PDF Diagram
       
    Shipping not included with this new item
    To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
    Details
  • Binder vacuum oven 1.9

    Binder Vacuum Oven 1.9

    $13,500.00

    A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.

    Benefits

    • Fast and gentle drying
    • Direct heat transfer through large thermal conducting plates
    • Safe work with one-of-a-kind safety concept
    • Coordinated, modular system with vacuum pump and vacuum module
    • 2 year warranty

    Important characteristics

      • Temperature range: room temperature plus 15 °C to 200 °C
      • ATEX compliance chamber's interior: Ex II 3/-G Ex h IIB T1-T3 Gc X
      • APT.line™ preheating chamber technology
      • Controller with time-segment and real-time programming
      • 2 aluminum expansion racks
      • Inert gas connection
      • Shatterproof, spring-mounted safety glass panel
      • Pressurized instrument panel with compressed air connection
      • Pressure control device for heating activated < 125 mbar
      • Flame protection gasket
      • Class 2 independent adjustable temperature safety device (DIN 12880) with visual alarm
      • Computer interface: RS 422
    Performance Data Temperature
    Heating-up time to 100 °C [min] 80
    Temperature fluctuation [± K] 0.1
    Temperature range 15 °C above ambient temperature to [°C] 200
    Temperature variation at 100 °C [± K] 2
    Vacuum Data
    Leak rate [bar/h] 0.01
    Permitted end vacuum [mbar] 0.01
    Electrical data
    Nominal power [kW] 1.2
    Phase (Nominal voltage) 1~
    Power frequency [Hz] 50/60
    Rated Voltage [V] 230
    Unit fuse [A] 10
    Connections
    Compressed air connection for pressure-encapsulation 8 mm
    Inert gas connection with flow limiter (RP") 3/8
    Measuring access port with small flange [DN mm] 16
    Vacuum connection with small flange [DN mm] 16
    Housing dimensions not incl. fittings and connections
    Depth net [in] 21.67
    Height net [in] 30.53
    Width net [in] 25.02
    Internal Dimensions
    Depth [in] 13.4
    Height [in] 15.76
    Width [in] 15.76
    Measures
    Interior volume [cu.ft.] 1.9
    Load per rack [lbs] 44
    Net weight of the unit (empty) [lbs] 209
    Permitted load [lbs] 99
    Viewing window height [in] 12.1
    Viewing window width [in] 13.79
    Wall clearance back [in] 3.94
    Wall clearance sidewise [in] 5.32
    Fixtures
    Number of shelves (std./max.) 2/5
    1. All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
    Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here: PDF Diagram    
    Shipping not included with this new item
    To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
    Details
  • Binder vacuum oven 4.1

    Binder Vacuum Oven 4.1

    $17,500.00

    A BINDER safety vacuum drying oven ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber of the VDL safety vacuum drying oven is designed according to ATEX guidelines 2014/34/EU Ex II 3/-G Ex h IIB T1-T3 Gc X.

    Benefits

    • Fast and gentle drying
    • Direct heat transfer through large thermal conducting plates
    • Safe work with one-of-a-kind safety concept
    • Coordinated, modular system with vacuum pump and vacuum module
    • 2 year warranty

    Important characteristics

    • Temperature range: room temperature plus 15 °C to 200 °C
    • ATEX compliance chamber's interior: Ex II 3/-G Ex h IIB T1-T3 Gc X
    • APT.line™ preheating chamber technology
    • Controller with time-segment and real-time programming
    • 2 aluminum expansion racks
    • Inert gas connection
    • Shatterproof, spring-mounted safety glass panel
    • Pressurized instrument panel with compressed air connection
    • Pressure control device for heating activated < 125 mbar
    • Flame protection gasket
    • Class 2 independent adjustable temperature safety device (DIN 12880) with visual alarm
    • Computer interface: RS 422
    Performance Data Temperature
    Heating-up time to 100 °C [min] 95
    Temperature fluctuation [± K] 0.1
    Temperature range 15 °C above ambient temperature to [°C] 200
    Temperature variation at 100 °C [± K] 3.5
    Vacuum Data
    Leak rate [bar/h] 0.01
    Permitted end vacuum [mbar] 0.01
    Electrical data
    Nominal power [kW] 1.9
    Phase (Nominal voltage) 1~
    Power frequency [Hz] 50/60
    Rated Voltage [V] 230
    Unit fuse [A] 10
    Connections
    Compressed air connection for pressure-encapsulation 8 mm
    Inert gas connection with flow limiter (RP") 3/8
    Measuring access port with small flange [DN mm] 16
    Vacuum connection with small flange [DN mm] 16
    Housing dimensions not incl. fittings and connections
    Depth net [in] 26.4
    Height net [in] 35.46
    Width net [in] 29.16
    Internal Dimensions
    Depth [in] 18.12
    Height [in] 19.94
    Width [in] 19.94
    Measures
    Interior volume [cu.ft.] 4.1
    Load per rack [lbs] 44
    Net weight of the unit (empty) [lbs] 337
    Permitted load [lbs] 143
    Viewing window height [in] 16.27
    Viewing window width [in] 17.97
    Wall clearance back [in] 3.94
    Wall clearance sidewise [in] 5.32
    Fixtures
    Number of shelves (std./max.) 2/6
    1. All technical data is specified for unloaded units with standard equipment at an ambient temperature of +22 °C ±3 °C and a power supply voltage fluctuation of ±10%. The temperature data is determined in accordance to BINDER factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to change technical specifications at any time.
    Further information (Data Sheets, Operating Manuals and Technical Drawings) can be downloaded from BINDER. A Basic vacuum oven diagram can be seen/downloaded here: PDF Diagram    
    Shipping not included with this new item
    To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
    Details
  • RBF-12,000-3N-45

    Boiling Flask 12L-3N-45

    $874.99
    The Boiling Flask 12L-3N-45 is made from high quality Schott glass, this is the original Rundkolben (triple offset joints) 3 neck round bottom flask. The most popular and strongest distillation flask of its kind. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. Joints are standard taper 24/40 (2) and 45/50 main. 12 Liter flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 12L-3N-45
    Add to cart Details
  • 6×48 Chromatography Column

    Chroma Column FF 6×48

    $1,999.99
    Chroma Column FF 6x48 with coarse/fine mixed frit and heavy wall thickness of 3mm. Special design allows for #29 Fraction Finder that permits you to check your fraction and watch your progression. Attach a FF between the frit and the stopcock area. Comes with rodaviss , GL18 and #45 Chroma Cap. Fraction Finder not included. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! Please use this column at your own risk! In addition to lab stands, it is recommended that you secure the lab stands to a wall or sturdy foundation while also using sandbags. This column will surpass 100+ lbs of weight holding full fluid. Please make sure you are offsetting the weight of your fluids. Summit requires this chromatography column to be supported by 3 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not included) to maximize grip. This column may slip though clamps if not properly bottom supported. Recommended (yet again), to have a lab tripod base (use rubber stripping here as well) or a circular clamp about 5" diameter (not included)(last picture). The Chroma Column FF 6x48 has no warranty. https://www.instagram.com/p/B5Lv5CzBAS-/ As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's. Stands, clamps, sandbag and Fraction Finder are not included.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chroma Column FF 6x48
    Add to cart Details
  • 4×36 Chromatography Column

    Chromatography Column 4×36

    $1,099.99
    Chromatography Column 4x36 (inches) with coarse/fine mixed frit. Heavy wall thickness of 3mm. Comes with Rodaviss connection and 45/50 Chroma Cap (GL14 feed/vacuum port). The drain has a PTFE stopcock to GL18. All GLs are included. Chroma Cap has elongated recessed port with diffuser. This directs fluid spray against walls to gently fill the column and protect media from movement. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! To comply with warranty, Summit requires this chromatography column to be supported by 2 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not shown) to maximize grip. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's. Lab stands and clamps not included.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chromatography Column 4x36
    Add to cart Details
  • 4×48 Chromatography Column

    Chromatography Column 4×48

    $1,299.99
    Chromatography Column 4x48 (inches) with coarse/fine mixed frit. Heavy wall thickness of 3mm. Comes with Rodaviss connection and 45/50 Chroma Cap (GL14 feed/vacuum port). The drain has a PTFE stopcock to GL18. All GLs are included. Chroma Cap has elongated recessed port with diffuser. This directs fluid spray against walls to gently fill the column and protect media from movement. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! To comply with warranty, Summit requires this chromatography column to be supported by 2 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not shown) to maximize grip. For this larger size column, Summit requires applying weight to the stand base such as a sand bag or something equivalent of 50 lbs+ (something to offset the weight of your fluids) As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chromatography Column 4x48
    Add to cart Details
  • Sale!
    5×48 Chromatography Column

    Chromatography Column 5×48

    Original price was: $1,700.00.Current price is: $749.99.
    Chromatography Column 5x48 (inches) with coarse/fine mixed frit. Heavy wall thickness of 3mm. Comes with Rodaviss connection and 45/50 Chroma Cap (GL14 feed/vacuum port). The drain has a PTFE stopcock to GL18. All GLs are included. Chroma Cap has elongated recessed port with diffuser. This directs fluid spray against walls to gently fill the column and protect media from movement. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! In addition to lab stands, it is recommended that you secure the lab stands to a wall or sturdy foundation while also using sandbags. This column will surpass 80+ lbs of weight holding full fluid. Please make sure you are offsetting the weight of your fluids. Summit requires this chromatography column to be supported by 3 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not included) to maximize grip. This column may slip though clamps if not properly bottom supported. Recommended (yet again), to have a lab tripod base (use rubber stripping here as well) or circle clamp base about 4″ diameter (not included)(last picture). Stands , clamps and sandbag are not included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chromatography Column 5x48
    Add to cart Details
  • Sale!
    6×48 Chromatography Column

    Chromatography Column 6×48

    Original price was: $2,000.00.Current price is: $1,699.99.
    Chromatography Column 6x48 (inches) with coarse/fine mixed frit and heavy wall thickness of 3mm. Comes with Rodaviss connection and 45/50 Chroma Cap (GL14 feed/vacuum port). The drain has a PTFE stopcock to GL18. All GLs are included. Chroma Cap has elongated recessed port with diffuser. This directs fluid spray against walls to gently fill the column and protect media from movement. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! Please use this column at your own risk! In addition to lab stands, it is recommended that you secure the lab stands to a wall or sturdy foundation while also using sandbags. This column will surpass 100+ lbs of weight holding full fluid. Please make sure you are offsetting the weight of your fluids. Summit requires this chromatography column to be supported by 3 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not included) to maximize grip. This column may slip though clamps if not properly bottom supported. Recommended (yet again), to have a lab tripod base (use rubber stripping here as well) or circle clamp about 5" diameter (not included)(last picture). The 6x48 Chromatography Column has no warranty. Stands , clamps and sandbags not included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chromatography Column 6x48
    Add to cart Details