-
Sale!
Chromatography Column 6x48 (inches) with coarse/fine mixed frit and heavy wall thickness of 3mm. Comes with Rodaviss connection and 45/50 Chroma Cap (GL14 feed/vacuum port). The drain has a PTFE stopcock to GL18. All GLs are included. Chroma Cap has elongated recessed port with diffuser. This directs fluid spray against walls to gently fill the column and protect media from movement. All of our chromatography columns now have option to add an Ultra Sensitive Fraction Finder! Please use this column at your own risk! In addition to lab stands, it is recommended that you secure the lab stands to a wall or sturdy foundation while also using sandbags. This column will surpass 100+ lbs of weight holding full fluid. Please make sure you are offsetting the weight of your fluids. Summit requires this chromatography column to be supported by 3 chain clamps and a top mounted cork clamp. Summit recommends applying a thin rubber strip (the length of the chains contact) under the chain clamps (not included) to maximize grip. This column may slip though clamps if not properly bottom supported. Recommended (yet again), to have a lab tripod base (use rubber stripping here as well) or circle clamp about 5" diameter (not included)(last picture). The 6x48 Chromatography Column has no warranty. Stands , clamps and sandbags not included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment you deserve for all your chromatography and CRC proccess's. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chromatography Column 6x48 -
Chromotography Cap 45 comes with Rodaviss and (2) GL14s. Cap has elongated recessed port with diffuser to direct fluid spray against column walls. Gently fill the column and protect your media from movement. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Chromotography Cap 45 -
$39,000.00
Summit Research's USA manufactured, peer reviewable Closed Loop Systems (CLS) is the highest quality system in the industry. The standard purchase package, as shown, is a passive system with a built in cryogenic cooler. The system does not require chillers to operate as it was designed to heat on the recovery side, generating vapor for recovery via the coil condensation of the hydrocarbons. Included:- Populated Rack with Material Column
- Filtration Sock
- CRC/Remediation
- Collection Column
- Drier
- Complete Swagelok Tubing and Attachments
- Valves
- Supports
- Safety Valves/PRV's
- ASME Solvent Storage Tank
- Plate Exchanger (For use with LN2 or Chiller)
- Recovery Coils
- Jacketed Vessels
Additional options that can be added:- Recovery pump
- Heaters
- Ancillary hardware
With a 360 design the CLS fits the most features into the smallest footprint on the market allowing for ease of use while taking up a limited amount of space. (Plated Heat Exchanger now incorporated into base of this unit for even smaller footprint) This versatile system combines features for both crude cannon work and detailed high grade tuned extractions into one. No feature or expense is spared in the manufacturing of Summit Research's CLS allowing customers top of the line equipment at an affordable price.
One of our customers using the CLS: Instagram Demo 
To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing. -
Sale!
The Cold Trap 1 34 to GL (CT-1 semi-classic) is a borosilicate glass trap with 34/45 port to dual GL18 to the pump. Traditional cold trap design to throw down wet vapor and keep your pumps dry. Comes complete with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Clamps and stands not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 1 34 to GL -
Sale!
The Cold Trap 1 GL to GL (CT-1 Classic) is a borosilicate glass trap with GL18 port to dual GL18 to the pump. Traditional cold trap design to throw down wet vapor and keep your pumps dry. Comes complete with: Clamps and stands not included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 1 GL to GL -
The Cold Trap 2 (CT-2 Inv Cup) sets itself apart from others with its patented inverse cup technology. Vapors enter the cup, creating a turbulent vortex, then are forced to condense straight down ensuring proper dry vacuum protection to the pumps. Most traditional traps bypass vapors, only relying on cold surfaces, while this trap prevents nearly all vapors from bypassing. This trap comes with hard pipe to pumps. 34/45 female inlet and female outlet. 45/50 flask port. Included with: Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distlllation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 2 -
Cold Trap 2 Hard Pipe with male 34/45 (from cold trap) and 34/45 female exit (to pumps). The straight pipe acts as a sight glass and is a great last line of defense to see if any moisture is reaching your pumps. Total length: 24.5 inches and 3.5 inches at top section. Hard pipe only, cold trap not included. Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distillation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. CT-2 Hard Pipe -
The Cold Trap 2 Shorty (CT-2 Inv Cup Shorty) sets itself apart from others with its patented inverse cup technology. Vapors enter the cup, creating a turbulent vortex, then are forced to condense straight down ensuring proper dry vacuum protection to the pumps. Most traditional traps bypass vapors, only relying on cold surfaces, while this trap prevents nearly all vapors from bypassing. 34/45 female inlet and male outlet. 45/50 flask port. Comes included with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 2 Shorty -
The Cold Trap 3 is a liquid cooled triple coiled beast! Eliminate the need for dry ice in your lab and hook up to a chiller. Female 34/45 inlet and outlet provides the bore your vacuum pumps desire. Extreme duty capacity and redesigned custom sized parallel flow coils that supply you with unmatched cooling. Daisy chain your chiller hosing top to bottom to include the Cold Trap 3 Flask. Collection flask port 45/50.- Heavy wall and joint thickness. Upgraded GL18 connections prevent barb breakage and mass body failure from stress of removing hoses.
- 1 Liter liquid jacketed collection flask made with extra thick glass and extra thick joints using gl14s to the chiller.
- Shorter overall height (21" please refer to schematic) allowing smaller footprint compared to other 1 liter collection cold traps. Allows closer placement to your work area with small stands compared to the typical wall mount or 42-44" iron foot stands.
- Cold Trap 3 can be used to collect florals/terps, and using the lower flask you can reheat and steam the vapors up, re-condensing even 20ml of liquid up and back down to wash your florals/terps to the lower flask for capture and processing.
- Cold Trap 3 Flask
- Rodaviss
- Gl14 (2)
- GL18 (2)
-
Sale!
The Cold Trap 3 Flask (CT-3 Flask) eliminates the need for dry ice in your lab! 45/50 Joint with threading for Rodaviss. Jacketed 1 Liter cold trap flask with extra thick (3mm) Schott glass. GL14 inlet and outlet to the chiller. Get the whole setup with the Summit Research Cold Trap-3 GEN2 that is capable of enormous vacuum concentration and is completely liquid cooled. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. GL14s included. Rodaviss kit not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 3 Flask -
When the going gets tough, you can't ever be too safe! A triple coil intermediate trap with female 34/45 inlet and male outlet. This trapping mechanism is used as a laminar path connection recommended for larger short path distillation setups (22-50L) leading into dual cold traps. Heavy wall and joint thickness. Upgraded GL18 connections prevent barb breakage and mass body failure from stress of removing hoses. Extreme duty capacity and redesigned custom sized parallel flow coils that supply you with unmatched cooling. Collection flask port 45/50. Comes complete with: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap 3 Shorty -
The 45/50 threaded Cold Trap Cap commonly attaches to a Summit Cold Trap. Used in conjunction with the Rodaviss Screw Cap. Glassware for maximum efficiency short path distillation. Made in USA. Rodaviss not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Cold Trap Cap
