-
Hochstrom O-rings (2 included) that fits at the bottom of your Hochstrom filter™. Made from Viton, a synthetic rubber and fluoropolymer elastomer, that is chemical-resistant. 100% USA made. -
KF16 O Ring will fit between any KF16 flange while using a KF16 clamp. Made from Viton and stainless steel. -
$4,999.99
The new SPD-8 Series Heads (FC55, 60mm, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. This 2 liter head comes with boiling flask! Can be upgraded to 5 liter flask, please call us. Short Path Distillation 8 Head in use at the lab: Instagram Demo
The condenser in this 60mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm.
Included with this head:
- Head Key Well 45/50
- Stopper Well 45/50
- High Temp GL18s (4)
- Flange Clamp 60mm
- PTFE O-Ring 60mm
- 2 Liter Boiling Flask
-
$2,800.00
The Sogevac single stage rotary vane pumps are required for any sized hardpiped system and can be very useful on hosed systems as well.- Inlet: KF40
- Motor: 1 Phase, 180/264V, 50/60Hz, 1.5kW, 12A
- Oil: synthetic hydrocarbon
- Pumping speed: 31 CFM (60Hz)
- Ultimate pressure: 0.5 mbar
- Compact design and small footprint
- Very low and constant noise level in any working condition
- Simplified maintenance
-
$3,400.00
Simple yet powerful, the GVS40A uses displacement and horsepower to achieve CFM. Unlike many other types of pumps that require complex fore traps, cryotraps, etc. – a well maintained single stage rotary vane can withstand great amounts abuse; making them very affordable and usable without much worry. Also know as 'roughing', 'wet' or 'backing' pumps. The GVS40A rotary vane pump is required for any sized hard-piped system and can be very useful on hosed systems as well.- Inlet: KF25
- Exhaust: 1 1/4" female threaded (ID)
- Motor: 1 Phase, 180/264V, 50/60Hz
- Oil: synthetic hydrocarbon
- Pumping speed: 31 CFM (60Hz)
- Ultimate pressure: 0.4 Torr
-
$14,999.99
New GVD80 + New EMF100 Filter + 5 gal oil Edwards GVD80 series two stage oil sealed rotary vane vacuum pumps are renowned for their high ultimate vacuum, rapid pumping speeds, quiet operation and ability to handle water vapor. These direct drive rotary vane pumps are inherently compact and vibration free, and with their finger-proof fan and coupling housings they offer excellent operator protection. We also carry GVD28s for smaller applications. We get our pumps from a thermo fisher service and testing centers. Some are brand new never used. Some are used for 30 days to 30 hours max. All are chemically cleaned, and restored to brand new condition with 99-100% test motors with factory Edwards full parts kit. Everything replaced. Comes with a 6 months unconditional warranty other than direct misuse. This beast is ready to serve you.Pump comes with :- GVD80 pump 3-phase
- 5 gallons I 19 Standard
- New EMF100 filter
- Comes standard with KF40 connections