-
Pressurized fluid and solution stainless steel handling keg. 2 inch diameter tri-clamp. Full chemical duty. Choice of 5 gallon or 15 gallon. Whether running hot or cold, pressurized or not, these durable kegs get the job done. Made in USA. Comes with clamp, o-ring, two port lid and 3/8 nipples. Keg measures 26inches x 15.5inches. -
The Valved Coil-less Laminar 34 allows you to isolate your joint with a PTFE threaded valve. Enables you to swap out your receiving flask without loosing vacuum. With this option, simply lower the valve and unscrew the GL cap to release the vacuum to change your flask. Comes complete with 24/40 Stopper, all necessary keck clips, GL14 cap and choice of #24/40 KF25 adapter. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Valved Coil-less Laminar 34 -
Sale!
ROCK BOTTOM Clearance Sale! While supplies last. Boiling Flask 2L-3N-24 is made from high quality Schott glass and is the original Rundkolben (triple offset joints) 3 neck round bottom flask. The most popular and strongest short path distillation flask of its kind. All joints are standard taper 24/40. 2 Liter flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 2L-3N-24 -
24/40 Continuous oil/water separator for terpene extraction. Isolates oil both lighter and heavier than water. Comes equipped with PTFE flow control valve (stopcock). For many different seperations. Find similar and corresponding parts in our Terpene Glassware section. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Terpene Oil/Water Separator -
KF16x10 Centering Ring. Viton rubber and stainless steel. Used with breather valves and barbs. Comes in the KF Breather Valve Kit. 100% USA made. -
KF16 O Ring will fit between any KF16 flange while using a KF16 clamp. Made from Viton and stainless steel. -
Billet stainless steel adapter that reduces the diameter of your KF vacuum pipe. KF40 to KF25 flange. Summit has corresponding KF25 and KF40 products in our Stainless Steel section. -
The Boiling Flask 22L-3N-100mm is made from high quality Schott glass, and is the original Rundkolben (triple offset joints) flask. The most popular and strongest short path distillation flask of its kind. Made specifically for Summit MPD heads. The dimensions and geometry of the joints are original concepts brought to market by Summit Research. Joints are standard taper 24/40 (2) and 100mm main flange. 22 Liter round bottom flask. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. O-ring and clamp not included (comes with any MPD head) Other sizes to choose from: Summit recommends all users to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use. We are not responsible or liable for loss of subsequent hardware contamination/failure with or without the result of damaged surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Boiling Flask 22L-3N-100 -
Laminar No Discharge 34 is a shorter, more compact unit which allows for higher temperatures in the vapor bypass. Coil-less laminar with less turbulence and no discharge. Comes with #24 glass stopper and choice of #24/40 KF25 adapter. Moreover, these short path distillation arms are used in conjunction with a Swing Arm Kit. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Laminar No Discharge 34 -
Cold Trap 2 Hard Pipe with male 34/45 (from cold trap) and 34/45 female exit (to pumps). The straight pipe acts as a sight glass and is a great last line of defense to see if any moisture is reaching your pumps. Total length: 24.5 inches and 3.5 inches at top section. Hard pipe only, cold trap not included. Absolutely necessary XL Fork Clamp for the Hard Pipe of the Cold Trap 2. Not supporting your short path distillation setup properly will void any type of limited warranty. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. CT-2 Hard Pipe -
The Separatory Funnel 4 Liter comes with a Sep Funnel Cap 45 that has improved recessed port for increased velocity when self mixing. The application, with vacuum, will launch the washing solution into the loaded solution and properly mix them without ever having to remove the funnel from the stand. The PTFE flow control valve (stopcock) is equipped with GL18 for adequate flow and accurate shutoff. Threaded 45/50 port out the top for Rodaviss. High temp PTFE GL connectors, Rodaviss and cap all included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve whether you are water washing or terpene extracting and everything in between. Stands, clamps & supports not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Separatory Funnel 4 Liter -
Raschig Rings 8x8 are small pieces of borosilicate tube used in large numbers as a packed bed within columns for distillation. These glass rings provide a large surface area within the volume of the column for interaction between liquid and gas vapors. Rings actually measure 8x10mm in size. 1 Pound bag. Also available: Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Raschig Rings 8x8 -
Summit Research custom made 45 to 24 high friction terpene head is the ultimate steam distillation condenser. This head is excellent for low vacuum/inert gas cfm condensing from the initial pathway. A first phase head that removes the bulk of the energy prior, to a more efficient condenser, like a graham unit. This prevents spitting of a second condenser and allows the turbulence to convert to a steady stream into second condenser. GL14 adapters (2) and keck clip included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Terpene Head -
Premium Schott glass 24/40 plug. 8.25 inch overall length (6 inches from bottom of frosted taper) with 15 bands. Key well allows thermometer probe to enter the head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Head Key Well 15 Band 24/40 -
The KF40 Clamp combined with KF40 O Ring form a vacuum tight seal between the connection flanges. This circumferential clamp is used for connecting standard NW40 / KF40 vacuum components. Aluminum clamp with butterfly nut for easy tightening.
