spd head

  • The Short Path Distillation Head Bertha 100, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 100 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 2-4 liters per hour (6 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or-  sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our flanged heads fit exclusively to Summit MPD boiling flasks: Refer to our instructional (SPD-4 MPD Complete) for correct setup of this head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 100
  • The Short Path Distillation Head Bertha 150, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 150 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 4-6 liters per hour (8 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or-  sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our MPD heads fit exclusively to Summit MPD boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 150
  • Sale!
    The Short Path Distillation Head FC34 (spd-2 fc34) has been upgraded with our new fraction collector technology. This head runs specifically for smaller setups (2L & 5L). Equipped with #34 bore, #29 discharge arm and #24 key port. All tapers are traditional. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. This FC34 head holds a medium height and 2 levels of vigreux for medium rejection. A traditional all around head that will stand the test of time. Refer to our instructional (SPD-2 FC34 Complete) for correct setup of this head. GL14s and key included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC34
  • Sale!
    The Short Path Distillation Head FC45 Nano (Previously SPD-6 FC45 Nano) model includes 45/50 main bore with a 29/42 discharge and 24/40 thermoport. This Nano version has no vigreux bringing rejection to a minimum. But that can all change with the right head key. (This key is specially made for the Nano to maximize rejection) and is NOW included along with: When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are their heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with premium Schott glass. Refer to our instructional (SPD-6 FC45 Complete) for correct setup of this head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC45 Nano
  • Sale!
    The Short Path Distillation Head FC45 Shorty (Previously SPD-6 FC45 Shorty) model includes 45/50 main bore with a 29/42 discharge and 24/40 thermoport. This Shorty version comes equipped with vigreux, adding an element of rejection. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are their heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with premium Schott glass. See the SPD6 in action: Instagram Demo instagram logo As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. GL14s, key and well stopper included. Refer to our instructional (SPD-6 FC45 Complete) for correct setup of this head.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC45 Shorty
  • Sale!
    The Short Path Distillation Head FC45 Tall (Previously SPD-6 FC45 Tall) model includes 45/50 main bore with a 29/42 discharge and 24/40 thermoport. This is the tallest of our FC45 models for more selectivity and reduced speeds. It has multiple rows of vigreux adding more rejection. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are their heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with premium Schott glass. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. GL14s, key and well stopper included. Refer to our instructional (SPD-6 FC45 Complete) for correct setup of this head.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC45 Tall
  • The Short Path Distillation Head FC55 Nano (Previously SPD-6 FC55 Nano) model includes 55/50 main bore with a 34/45 discharge and 34/45 thermoport. This Nano version has no vigreux bringing rejection to a minimum. But that can all change with the right head key. (This key is specially made for the Nano to maximize rejection) and is NOW included along with: When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with Schott glass. There are two recommended options with varying pumps, diffusion and total liters: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC55 Nano
  • Short Path Distillation Head FC55 Shorty models include 55/50 main bore with a 34/45 discharge and thermoport. This Shorty version comes equipped with vigreux, adding an element of rejection. See the SPD6 in action: Instagram Demo instagram logo When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with Schott glass. GL14s, key and well stopper included. There are two recommended options with varying pumps, diffusion and total liters: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC55 Shorty
  • Short Path Distillation Head FC55 Tall models include 55/50 main bore with a 34/45 discharge and thermoport. This is the tallest of our FC55 models for more selectivity and reduced speeds. It has multiple rows of vigreux adding more rejection. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with Schott glass. GL14s, key and well stopper included. There are two recommended options with varying pumps, diffusion and total liters: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC55 Tall  
  • The Short Path Distillation Head FC71 includes a 71/60 main bore with a 34/45 discharge and 34/45 thermoport. The 71 mm can handle bigger systems and a lot of product. A very versatile head that we can cater towards your needs. Comes with 34 key, 34 stopper well and GL14s. This limited edition short path distillation head (along with boiling flask) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with these boiling flasks: Summit has 5L and 12L options for this head. Please call us for more information. Clamp and stands not included.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC71
  • HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB1 100 comes equipped with 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB1 100, or previously SPD-4 MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB1 is designed to be ultra selective to evacuate all previous fractions before the main body without letting the main body through. With some temp, main body can come out extremely fast and this head can be used as a first pass head. It is very effective in removing heads fractions while retaining main body components. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Please contact us for a completely tuned system with this hardware! Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR-  sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature.  Effectively increasing the stock speed and lowering the temperatures further. The HB1 100mm head comes with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Boiling flask not included.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 100 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified.
  • HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB1 150 comes equipped with 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB1 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB1 is designed to be ultra selective to evacuate all previous fractions before the main body without letting the main body through. With some temp, main body can come out extremely fast and this head can be used as a first pass head. It is very effective in removing heads fractions while retaining main body components. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Please contact us for a completely tuned system with this hardware! Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR-  sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature.  Effectively increasing the stock speed and lowering the temperatures further. The HB1 150mm head comes with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified.
  • $4,499.99

    The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo instagram logo 100mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 100mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.     Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 100 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
  • $4,849.99

    The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo instagram logo 150mm clamp, O-ring and PTFE GL18s (4) included. Has 34/45 discharge port with built in key. Our 150mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.     Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 Halo 150 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
  • PLEASE CALL FOR AVAILABILITY. HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB2 100 comes equipped with 34/45 key port, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB2 100, or previously SPD-4 MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB2 is designed to be ultra high speed with precision refinement. This head was bench marked by Heisenberg on a dual e2m30 array achieving 6 liters per hour without any effort at all. This head can be setup for very low temperatures, high clarity, and high speeds. Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR-  sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature.  Effectively increasing the stock speed and lowering the temperatures further. The HB2 100mm head comes included with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.   Base not included.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 100
  • PLEASE CALL FOR AVAILABILITY. HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB2 150 comes equipped with 45/50 key port, 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB2 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB2 is designed to be ultra high speed with precision refinement. This head was bench marked by Heisenberg on a dual e2m30 array achieving 6 liters per hour without any effort at all. This head can be setup for very low temperatures, high clarity, and high speeds. Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR-  sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature.  Effectively increasing the stock speed and lowering the temperatures further.   The HB2 150mm head comes included with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified.
  • $4,299.99

    The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo instagram logo 34/45 key, 100mm clamp with O-ring and PTFE GL18s (4) included. 34/45 discharge port. Our 100mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.     Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 100 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
  • $5,224.99

    The HB Series Halo heads are inspired by our original fraction collector technology and have taken theses concepts to a new level. Halo technology allows for liquid temperature modulation at the top the head, dialing in your temps at a point in your short path distillation never before achieved. See the Halo in action: Instagram Demo instagram logo 150mm clamp with O-ring and PTFE GL18s (4) included. 45/50 Key port and appropriate key & well stopper. 34/45 discharge port. Our 150mm heads fit exclusively to Summit flanged boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.     Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB2 Halo 150 To purchase, please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. Price does not include shipping and will be included in your final estimate before processing.
  • First of its kind, innovation and performance meet the future of distillation. The Ultra Short Path Distillation Head (previously SPD-7) is a fascinating technology inspired by an ultra low temperature process. The Summit research SPD-7 is a horizontal head designed to fully refine products at a low temperature; preferred material required should be refined previously, or physically refined through all filtration and washing/chroma processes prior to running through this system. Material must be completely dried and full vacuum cannot be engaged if material is wet. Do not attempt to load green/black crude material. This system requires much more vacuum requirement so please keep in mind the 22 liter system takes a diffusion, and the 5 liter system can use dual e2m28/30. With a high flow triple condenser coil to GL18 adapters, the temps are dialed in throughout this horizontal head. Big bore 55/50 inlet and outlet with a traditional 29/42 discharge to flask. Wait, there's more! This head acts as a large swing arm, so you can swing and engage the flask to your targeted fraction. See the SPD7 in action (pt1): Instagram Demo instagram logo See the SPD7 in action (pt2): Instagram Demo instagram logo Head, KF25 adapter and GL18s (2) included. Glassware (boiling flask & cold trap) exclusive to this ultra short path head: Here is a complete look at the SPD-7 USPD setup. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your ultra short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Ultra Short Path Distillation Head
  • First of its kind, innovation and performance meet the future of distillation. The Ultra Short Path Distillation Micro Head (previously SPD-7.1) is a fascinating technology inspired by an ultra low temperature process. The Summit research SPD-7.1 is a horizontal head designed to fully refine products at a low temperature; preferred material required should be refined previously, or physically refined through all filtration and washing/chroma processes prior to running through this system. Material must be completely dried and full vacuum cannot be engaged if material is wet. Do not attempt to load green/black crude material. This system requires much more vacuum requirement so please keep in mind the 22 liter system takes a diffusion, and the 5 liter system can use dual e2m28/30. With a high flow dual condenser coil to GL18 adapters, the temps are dialed in throughout this horizontal head. Big bore 45/50 inlet and outlet with a traditional 29/42 discharge to flask. Wait, there's more! This head acts as a large swing arm, so you can swing and engage the flask to your targeted fraction. See the SPD7 in action (pt1): Instagram Demo instagram logo See the SPD7 in action (pt2): Instagram Demo instagram logo Head, KF25 adapter and GL18s (2) included. Glassware (boiling flask & cold trap) exclusive to this ultra short path head: For a complete look at SPD-7.1 Micro USPD setup: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your ultra short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Ultra Short Path Distillation Micro Head
  • The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo instagram logo The condenser in this 55/50 head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. 45 Key Well, 45 Well Stopper and GL18s (4) included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head FC55
  • The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo instagram logo The condenser in this 100mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Boiling flask not included.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head 100
  • $4,999.99

    The new SPD-8 Series Heads (FC55, 60mm, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. This 2 liter head comes with boiling flask! Can be upgraded to 5 liter flask, please call us. Short Path Distillation 8 Head in use at the lab: Instagram Demo instagram logo The condenser in this 60mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Micro Head To purchase, please contact Summit Research at 8312262948 or by eMail. Limited run items ship 1-3 days after orders have been processed unless otherwise specified.
  • The new SPD-8 Series Heads (FC55, 100mm, 150mm) bring a fraction collecting core combined with condenser coil. If you want absolute temperature control in a head, look no further. With these types of heads, if you dip the coil temp down it will act as a violent collection of molecules dragged to the coil like a magnet. That coil would inherently distribute those lower temps right on the surface of the fraction collector dish and that would display a whole new set of efficiency within the head. All Short Path Distillation 8 Heads have a 45/50 thermoport and a 34/45 discharge arm. Short Path Distillation 8 Head in use at the lab: Instagram Demo instagram logo The condenser in this 150mm head absorbs as much heat as possible and removes BTU energy from the vapor prior to entering the condenser arm. This allows the vacuum jacketed head to operate like it’s supposed to. The coil in the head doesn’t disturb molecular flow dynamics as it’s duty is to absorb heat before the heat affects the sides of the walls of the fraction collector as well as allows those ambient vacuum void temps to be more stable. When you get blow by in a head it means it’s just working overtime because the arm sends back fluids to the heater chiller and it can’t maintain the BTU heat removal. So if you can maintain exact temps you can bounce unwanted fractions right out of the condenser arm without over shooting flow rates. This maintains a drier vacuum in the condenser arm. Included with this head: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.       Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation 8 Head 150