-
The Short Path Distillation Head Bertha 100, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 100 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 2-4 liters per hour (6 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our flanged heads fit exclusively to Summit MPD boiling flasks: Refer to our instructional (SPD-4 MPD Complete) for correct setup of this head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 100 -
The Short Path Distillation Head Bertha 150, since development in 2018, has become one of the leading standards in distillation head types in the industry. 2023 has brought the Bertha 100 to its final perfect form with 6 generations of evolution. This head comes equipped with 45/50 thermoport, 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head Bertha 150 (previously SPD-4 MPD Big Bertha) is an extremely high vapor fractionation column head. The first section starts in the flask to retain as much heat in the column as possible. This entire column and entry into flask is isolated from the outside air and the flange fittings. The first chamber is a rough fractionation chamber with a lower rejection section that prevents any condensate from moving upwards. The center section is a secondary refinement section and will further refine the vapors. The upper third section is our patented fraction collector. The first dual stage fractionation column to ever be invented or used in distillation glassware, pilot or small scale. Can achieve 4-6 liters per hour (8 liters per hour with upgraded chilling and vacuum accessories) first pass and ready for crystallization. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Requirement to use these heads would be a sogevac + dual e2m30 -or- sogevac + e80 -or- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. Included: Our MPD heads fit exclusively to Summit MPD boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head Bertha 150 -
Sale!
The Short Path Distillation Head FC34 (spd-2 fc34) has been upgraded with our new fraction collector technology. This head runs specifically for smaller setups (2L & 5L). Equipped with #34 bore, #29 discharge arm and #24 key port. All tapers are traditional. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. This FC34 head holds a medium height and 2 levels of vigreux for medium rejection. A traditional all around head that will stand the test of time. Refer to our instructional (SPD-2 FC34 Complete) for correct setup of this head. GL14s and key included. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC34 -
Sale!
The Short Path Distillation Head FC45 Nano (Previously SPD-6 FC45 Nano) model includes 45/50 main bore with a 29/42 discharge and 24/40 thermoport. This Nano version has no vigreux bringing rejection to a minimum. But that can all change with the right head key. (This key is specially made for the Nano to maximize rejection) and is NOW included along with: When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are their heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with premium Schott glass. Refer to our instructional (SPD-6 FC45 Complete) for correct setup of this head. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC45 Nano -
Sale!
The Short Path Distillation Head FC45 Shorty (Previously SPD-6 FC45 Shorty) model includes 45/50 main bore with a 29/42 discharge and 24/40 thermoport. This Shorty version comes equipped with vigreux, adding an element of rejection. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are their heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with premium Schott glass. See the SPD6 in action: Instagram Demo
As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process.
GL14s, key and well stopper included.
Refer to our instructional (SPD-6 FC45 Complete) for correct setup of this head.
Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC45 Shorty -
Sale!
The Short Path Distillation Head FC45 Tall (Previously SPD-6 FC45 Tall) model includes 45/50 main bore with a 29/42 discharge and 24/40 thermoport. This is the tallest of our FC45 models for more selectivity and reduced speeds. It has multiple rows of vigreux adding more rejection. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are their heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with premium Schott glass. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. GL14s, key and well stopper included. Refer to our instructional (SPD-6 FC45 Complete) for correct setup of this head. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC45 Tall -
The Short Path Distillation Head FC55 Nano (Previously SPD-6 FC55 Nano) model includes 55/50 main bore with a 34/45 discharge and 34/45 thermoport. This Nano version has no vigreux bringing rejection to a minimum. But that can all change with the right head key. (This key is specially made for the Nano to maximize rejection) and is NOW included along with: When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with Schott glass. There are two recommended options with varying pumps, diffusion and total liters:- SPD-6 FC55 Optional Diffusion Mixed setup using 5/12/22 liter boiling flasks.
- SPD-6 FC55 Complete For a setup utilizing the 22L boiling flask and diffusion.
-
Short Path Distillation Head FC55 Shorty models include 55/50 main bore with a 34/45 discharge and thermoport. This Shorty version comes equipped with vigreux, adding an element of rejection. See the SPD6 in action: Instagram Demo
When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day.
The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with Schott glass.
GL14s, key and well stopper included.
There are two recommended options with varying pumps, diffusion and total liters:
- SPD-6 FC55 Optional Diffusion Mixed setup using 5/12/22 liter boiling flasks.
- SPD-6 FC55 Complete For a setup utilizing the 22L boiling flask and diffusion.
-
Short Path Distillation Head FC55 Tall models include 55/50 main bore with a 34/45 discharge and thermoport. This is the tallest of our FC55 models for more selectivity and reduced speeds. It has multiple rows of vigreux adding more rejection. When Summit Research initially released the first fraction collector technology we knew it would be a hit. We have innovated the newest distillation technology with the industry leading high-efficiency heads. We have retrofitted all Summit Research heads to incorporate our patented distillation technology. These heads rival wiped film speeds at a fraction of the cost, and higher clarity/purity/speed. The fraction collector head offers extremely high-efficiency operational parameters unparalleled to anything available on the market. Summit delivers solutions and results to our customers coming from extensive research and design in the field of high speed, high potency, low temperature, consistent distillations day after day. The differences between the FC series heads are the heights. Lower height heads will have less selectivity with faster speeds and lower temps, taller heads will have slightly slower speeds with slightly higher temps with more selectivity. Partnered with our patented laminar path technology and the inverted cup cold trap/hardpipe kits, our customers experience smooth, fast and consistent clarity time after time. We innovate where others imitate. 100% made in USA with Schott glass. GL14s, key and well stopper included. There are two recommended options with varying pumps, diffusion and total liters:- SPD-6 FC55 Optional Diffusion Mixed setup using 5/12/22 liter boiling flasks.
- SPD-6 FC55 Complete For a setup utilizing the 22L boiling flask and diffusion.
-
The Short Path Distillation Head FC71 includes a 71/60 main bore with a 34/45 discharge and 34/45 thermoport. The 71 mm can handle bigger systems and a lot of product. A very versatile head that we can cater towards your needs. Comes with 34 key, 34 stopper well and GL14s. This limited edition short path distillation head (along with boiling flask) is 'made to order' and carries longer lead times than most units. Please call us if you need an exact time frame. As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Fits exclusively with these boiling flasks: Summit has 5L and 12L options for this head. Please call us for more information. Clamp and stands not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head FC71 -
HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB1 100 comes equipped with 34/45 discharge port and a 100mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB1 100, or previously SPD-4 MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB1 is designed to be ultra selective to evacuate all previous fractions before the main body without letting the main body through. With some temp, main body can come out extremely fast and this head can be used as a first pass head. It is very effective in removing heads fractions while retaining main body components. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Please contact us for a completely tuned system with this hardware! Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. The HB1 100mm head comes with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Boiling flask not included. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 100 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified. -
HB series heads are inspired by our patented fraction collector technology paired with a larger flanged bore. Short Path Distillation Head HB1 150 comes equipped with 34/45 discharge port and a 150mm bore that secures to a boiling flask with o-ring and clamp. The Short Path Distillation Head HB1 150, or previously MPD (modified path distillation), was created for one of our testers Breaking Dabs aka Heisenberg. With his unique skills he has helped us tune the HB series heads to evolve and provide solutions for our users. HB1 is designed to be ultra selective to evacuate all previous fractions before the main body without letting the main body through. With some temp, main body can come out extremely fast and this head can be used as a first pass head. It is very effective in removing heads fractions while retaining main body components. Vigs are not needed for this technology due to the industry first "no-vig" approach which utilizes a baffled section that extends down below the head base and into the boiling flask. Please contact us for a completely tuned system with this hardware! Requirement to use these heads would be a sogevac + dual e2m30 -OR- sogevac + e80 -OR- sogevac + e80 + diffusion array. This particular setup benefits from a custom diffusion array and an Apollo Vacuum Controller with the inert gas sweeping feature. Effectively increasing the stock speed and lowering the temperatures further. The HB1 150mm head comes with: Our flanged heads fit exclusively to Summit boiling flasks: As always, Summit uses 100% best quality glass blanks that are THICKER and built BEYOND STANDARDS made right here in the USA. Our glassware is made specifically for efficiency and durability. Summit provides the quality of lab equipment that you deserve to streamline your short path distillation process. Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. Short Path Distillation Head HB1 150 Please contact Summit Research at 831-226-2948 or by eMail. Items ship 1-3 days after orders have been processed unless otherwise specified.
